2024 Jeep Grand Cherokee Oil Capacity & Specs

The 2024 Jeep Grand Cherokee takes 6.0 quarts (5.7 liters) of 0W-20 engine oil for the 3.6L Pentastar V6 engine, and 7.0 quarts (6.6 liters) of 5W-30 engine oil for the 5.7L HEMI V8 engine. It's crucial to use oil that meets the manufacturer's specifications to ensure optimal engine performance and longevity.

Quick Answer

• 3.6L Pentastar V6:

  • Oil Capacity: 6.0 quarts (5.7 liters)
  • Recommended Oil Weight: 0W-20
  • Oil Spec: FCA US LLC MS-6395 (or API SP / ILSAC GF-6A equivalent)
  • OEM Oil Filter P/N: Mopar 68507598AB
  • Aftermarket Cross-Reference:
    • Fram: CH12631
    • Wix: WL10010
    • Mobil 1: M1C-453A

• 5.7L HEMI V8:

  • Oil Capacity: 7.0 quarts (6.6 liters)
  • Recommended Oil Weight: 5W-30
  • Oil Spec: FCA US LLC MS-6395 (or API SP / ILSAC GF-6A equivalent)
  • OEM Oil Filter P/N: Mopar 68191349AB
  • Aftermarket Cross-Reference:
    • Fram: CH11665
    • Wix: WL10060
    • Mobil 1: M1-107A

Capacity by Engine Option

Oil Change Interval

Jeep recommends adhering to the following oil change intervals for your 2024 Grand Cherokee to maintain optimal engine health:

• Normal Duty: Every 10,000 miles (16,000 km) or 12 months, whichever comes first.
• Severe Duty: Every 5,000 miles (8,000 km) or 6 months, whichever comes first.

"Severe duty" conditions include frequent short trips, extensive idling, towing, dusty environments, or extreme temperatures. If you operate your vehicle under any of these conditions, it's wise to follow the severe duty schedule.

Drain Plug Torque

Properly torquing the drain plug is essential to prevent leaks and avoid damage to the oil pan.

• 3.6L Pentastar V6: 25 ft-lbs (34 Nm)
• 5.7L HEMI V8: 20 ft-lbs (27 Nm)

Always use a new crush washer with every oil change for a proper seal. Failure to do so can result in oil leaks.

How to Change the Oil

Changing the oil in your 2024 Jeep Grand Cherokee is a straightforward process for the DIY enthusiast. Here's a general overview:

1. Gather Supplies: Ensure you have the correct oil, oil filter, drain pan, wrench, torque wrench, and a new crush washer.
2. Warm Up Engine: Drive the vehicle for a few minutes to warm the oil, allowing it to drain more easily.
3. Lift and Secure: Safely lift the front of the vehicle using a jack and secure it with jack stands.
4. Locate Drain Plug: Place the drain pan beneath the oil pan and carefully remove the drain plug. Allow all the old oil to drain completely.
5. Remove Oil Filter: Locate and remove the old oil filter. Be prepared for some oil spillage.
6. Install New Filter: Apply a thin coat of new oil to the gasket of the new filter and install it by hand until snug, then tighten an additional 3/4 to 1 full turn.
7. Reinstall Drain Plug: Replace the drain plug with a new crush washer and torque it to the specified setting.
8. Add New Oil: Carefully pour the recommended amount and type of new oil into the engine through the oil filler cap.
9. Check Level: Start the engine and let it run for a minute, then shut it off. Wait a few minutes for the oil to settle and check the oil level with the dipstick, adding more if necessary.
10. Inspect for Leaks: Visually inspect around the drain plug and oil filter for any signs of leaks.
11. Reset Oil Life Monitor: Follow your vehicle's owner's manual instructions to reset the oil life monitoring system.

Common Issues / Tips

• ESS (Engine Stop-Start) System: Vehicles equipped with an ESS system may experience more frequent engine starts and stops. Using the correct oil specification (FCA US LLC MS-6395) is even more critical for engines with ESS due to the increased wear associated with frequent restarting.
• Oil Consumption (Pentastar V6): Some 3.6L Pentastar V6 engines, especially in previous generations, have been known to exhibit minor oil consumption. Regularly check your oil level between changes and top off as needed. While less common in newer generations, it's still a good practice.
• Oil Filter Housing (Pentastar V6): The oil filter housing on the 3.6L Pentastar V6 is located on top of the engine, making it relatively easy to access. However, ensure the o-rings are properly seated when replacing the filter to prevent leaks.
• Proper Oil Specification is Key: Using oil that does not meet the FCA US LLC MS-6395 specification can lead to premature engine wear and potential warranty issues. Always verify the oil you're using meets this requirement.

Need an oil change? Find a trusted shop on Repairius.