2024 Nissan Rogue Oil Capacity & Filter Specs

The 2024 Nissan Rogue takes 4.8 quarts (4.5 liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 4.8 quarts (4.5 Liters)
• Recommended Oil Weight: 0W-20
• Oil Type Specification: API SN PLUS, SP, or ILSAC GF-6A
• OEM Oil Filter Part Number: 15208-65F0E
• Aftermarket Oil Filter Cross-References:
  • Fram: PH10060
  • Mobil 1: M1-110
  • Wix: 57356

Capacity by Engine Option

All 2024 Nissan Rogue models are equipped with the KR15DDT 1.5L VC-Turbo 3-cylinder engine.

Oil Change Interval

Following Nissan's recommended maintenance schedule is crucial for the longevity of your 2024 Rogue's engine.

• Normal Duty: Change the engine oil and filter every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: If you operate your vehicle under severe conditions (e.g., frequent short trips, towing, extensive idling, dusty conditions, extreme temperatures), it is recommended to change the engine oil and filter every 5,000 miles or 6 months, whichever comes first.

Drain Plug Torque

The oil drain plug on the 2024 Nissan Rogue should be torqued to 25 ft-lbs (34 Nm). Always use a new crush washer (gasket) when performing an oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is typically 11026-JA00A.

How to Change the Oil

1. Warm up the engine: Drive the vehicle for a few minutes to bring the oil to operating temperature, ensuring it drains more easily.
2. Lift and secure: Safely lift the front of the vehicle using a jack and support it with jack stands. Never work under a vehicle supported only by a jack.
3. Locate drain plug: Place an oil drain pan beneath the oil pan. Locate the drain plug, usually a 14mm or 17mm bolt, on the bottom of the oil pan.
4. Drain oil: Carefully remove the drain plug (with a wrench or socket) allowing the old oil to drain completely into the pan. Be cautious, as the oil may be hot.
5. Replace drain plug: Once the oil has fully drained, clean the drain plug and install a new crush washer. Reinstall the drain plug and torque it to 25 ft-lbs (34 Nm).
6. Replace oil filter: Locate the oil filter (typically on the front or side of the engine block). Use an oil filter wrench to remove the old filter. Apply a thin film of new oil to the rubber gasket of the new filter before threading it on by hand until snug. Then, tighten an additional 3/4 to 1 full turn.
7. Add new oil: Lower the vehicle. Remove the engine oil fill cap and carefully pour in 4.8 quarts of fresh 0W-20 engine oil.
8. Check oil level: Start the engine and let it run for a minute to circulate the new oil. Turn off the engine, wait a few minutes for the oil to settle, then check the oil level using the dipstick. Add more oil if necessary, being careful not to overfill.
9. Dispose of old oil: Properly dispose of the used oil at a recycling center.

Common Issues / Tips

• VC-Turbo Engine Sensitivity: The KR15DDT 1.5L VC-Turbo engine is a sophisticated unit. Using the correct oil type and viscosity (0W-20) as specified by Nissan is critical for its performance and longevity. Using incorrect oil can lead to premature wear and potentially catalytic converter issues.
• Oil Consumption Considerations: Some turbocharged engines, including variable compression designs, may exhibit slight oil consumption between changes. Regularly check your oil level, especially if you drive under severe conditions, and top off as needed.
• Genuine Nissan Parts: While aftermarket filters are available, using a genuine Nissan oil filter ensures optimal fit and filtration performance as designed by the manufacturer.
• Gasket Kits: Some aftermarket oil filters may come with a new crush washer, but it's always a good idea to have a separate one on hand.

Need an oil change? Find a trusted shop on Repairius.