2024 Nissan Titan — Torque Specifications
Quick-reference fastener torques for wheels, oil and transmission drains, brakes, axle nut, spark plugs, valve covers, and intake manifold.
Working on this 2024 Nissan Titan? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Quick reference
| Fastener | Torque (ft-lb / Nm) | Notes |
|---|---|---|
| Wheel lug nuts | 98–154 ft-lb (133–209 Nm) | 6‑lug Titan models typically near 98 ft‑lb; 8‑lug Titan XD often higher (133–154 ft‑lb). Verify by trim/wheel. Torque in stages. |
| Engine oil drain plug | 25–30 ft‑lb (34–41 Nm) | Replace crush washer; torque on warm (not hot) engine. Clean threads. |
| Transmission drain plug (9‑speed auto) | 25–30 ft‑lb (34–41 Nm) | JR913E 9‑speed; use new gasket/O‑ring if equipped. Do not overtighten the pan. |
| Front brake caliper bracket bolts | 130–185 ft‑lb (176–251 Nm) | Higher end typical on XD. Clean threads; apply threadlocker only if specified by OEM. |
| Front brake caliper slide pins | 20–30 ft‑lb (27–41 Nm) | Use high‑temp silicone brake grease on pin boots and pin bodies (not threads unless specified). |
| Rear brake caliper bracket bolts | 70–118 ft‑lb (95–160 Nm) | Varies by axle/brake package (Titan vs. XD). Inspect for corrosion; replace if stretched. |
| Rear brake caliper slide pins | 18–28 ft‑lb (24–38 Nm) | Ensure free movement; seized pins cause taper wear and pulsation. |
| Front axle nut (4x4) | 173–259 ft‑lb (235–351 Nm) | Range covers Titan to XD; many applications require staking a new nut. Final torque with vehicle on ground unless procedure specifies otherwise. |
| Spark plugs (5.6L gas VK56VD) | 13–22 ft‑lb (18–30 Nm) | Torque on a cold engine. Dry install for nickel‑coated plugs (no anti‑seize) unless the plug maker directs otherwise. |
| Valve cover bolts | 62–89 in‑lb (7–10 Nm) | Inch‑pounds. Tighten in a criss‑cross, center‑out pattern in 2–3 passes. |
| Intake manifold – upper plenum bolts | 71–89 in‑lb (8–10 Nm) | Cross‑pattern. Recheck after a few minutes to account for gasket set. |
| Intake manifold – lower to cylinder head bolts | 15–22 ft‑lb (20–30 Nm) | Follow factory tightening sequence; torque in stages. |
Note: Ranges provided to cover differences between Titan and Titan XD, brake packages, and wheel hardware. Always confirm by VIN in the OEM service manual.
Wheel lug torque pattern
Use a star/cross pattern to seat the wheel evenly and prevent rotor or hub runout.
- 6‑lug wheels (most Titan): use a six‑point star pattern. Hand‑start all lugs, snug in sequence, then torque in two to three stages to final spec.
- 8‑lug wheels (Titan XD): use an eight‑point crisscross. Bring each fastener up evenly. After a short road test, recheck torque on aluminum wheels once cooled.
Helpful tips:
- Clean hub faces and wheel mating surfaces; remove rust and burrs.
- Tighten lug nuts dry unless the OEM specifies otherwise. Never lubricate stud/nut interfaces unless directed, as it changes clamping force.
- If using a torque stick, always verify final torque with a calibrated torque wrench.
Brake torque notes
- Caliper bracket bolts: Many trucks specify high torque to control caliper knock and pad taper. Clean threads with a wire brush/tap. If the service manual calls for threadlocker (often medium or high strength), apply only to clean, dry threads and replace any one‑time‑use bolts.
- Slide pins: Torque within the listed range and ensure pins slide freely. Use high‑temperature silicone brake lubricant on the smooth pin surfaces and under the boots; avoid getting grease on pad friction material or rotor faces. Do not use anti‑seize on pins.
- Rotor to hub seating: Any debris or rust behind the rotor will mimic a torque problem. Measure rotor runout after reassembly if you feel pulsation.
- Final check: After pumping the brake pedal to seat the pads, re‑verify caliper fastener torque.
Why torque matters
Correct torque establishes the intended clamping load without overstressing the fastener or the components it holds. Under‑torque risks loosening, noise, and uneven wear; over‑torque can stretch studs/bolts, distort rotors and hubs, crush gaskets, and complicate future service. Using a calibrated torque wrench and following the proper sequence (especially on multi‑fastener parts like wheels, valve covers, and intake manifolds) ensures even gasket compression and component alignment.
Important notes for the 2024 Titan:
- The 2024 Titan is gasoline‑only (5.6L VK56VD). Spark plug torque depends on plug design; follow the plug manufacturer’s instructions and the OEM spec within the range above.
- The Titan XD uses heavier hardware (8‑lug wheels, larger brakes), which generally drives higher torque values. Use the VIN to confirm build.
- Replace one‑time‑use hardware such as axle nuts and crush washers. Torque values assume clean, dry threads unless the OEM specifies oil, sealant, or threadlocker.
Disclaimer: This guide provides typical ranges for the 2024 Nissan Titan/Titan XD. Critical fasteners should always be verified against the OEM service manual for your exact VIN and option package. When in doubt, consult factory documentation or a professional technician.
Find a trusted shop on Repairius.
More specs for the 2024 Nissan Titan
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2024 Nissan Titan Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.
Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-10-10.