2015 Chevrolet Malibu Oil Capacity & Filter

The 2015 Chevrolet Malibu takes between 4.2 and 5.0 quarts of oil, depending on the engine. This guide provides a comprehensive overview of oil capacity, recommended oil types, filter part numbers, and maintenance tips for your 2015 Malibu.

Quick answer

• Oil Capacity:
  • 2.5L 4-cylinder: 5.0 Quarts (4.7 Liters)
  • 2.0L Turbo 4-cylinder: 5.0 Quarts (4.7 Liters)
  • 2.4L EcoTec 4-cylinder (Hybrid): 4.2 Quarts (4.0 Liters)
• Recommended Oil Weight: SAE 5W-20 or 5W-30 (refer to your owner's manual based on engine)
• Oil Spec: Dexos1 Gen2 or API SN Plus (or later).
• Oil Filter Part Numbers:
  • 2.5L & 2.0L Turbo:
    • OEM: ACDelco PF63F
    • Fram: PH10575
    • Wix: 57045
    • Mobil 1: M1-113
  • 2.4L EcoTec (Hybrid):
    • OEM: ACDelco PF48E
    • Fram: PH10060
    • Wix: 57060
    • Mobil 1: M1-105

Capacity by engine option

Oil change interval

Chevrolet recommends using the vehicle's Oil Life Monitoring (OLM) system to determine when to change your oil. This system takes into account various factors like driving style, temperature, and engine revolutions.

• Normal Duty: Typically, the OLM will recommend an oil change between 7,500 and 10,000 miles, or about once a year, whichever comes first.
• Severe Duty: If you frequently drive in demanding conditions (e.g., heavy towing, extreme temperatures, dusty environments, short trips, or stop-and-go traffic), your OLM will likely trigger an oil change sooner, potentially between 3,000 and 5,000 miles.

Always adhere to the OLM recommendations and consult your owner's manual for the most accurate information.

Drain plug torque

The drain plug torque for the 2015 Chevrolet Malibu is 18 lb-ft (25 Nm). It is highly recommended to replace the drain plug gasket or crush washer every time you perform an oil change to ensure a proper seal and prevent leaks.

How to change the oil

1. Warm up the engine: Drive the vehicle for a few minutes to bring the oil to operating temperature, allowing it to drain more easily.
2. Lift and secure: Safely lift the front of the vehicle using a jack and secure it with jack stands.
3. Locate drain plug: Place a suitable drain pan under the oil pan, then carefully remove the drain plug with a wrench.
4. Drain oil: Allow all the old oil to completely drain. This usually takes 10-15 minutes.
5. Replace drain plug: Install a new crush washer on the drain plug and tighten it to the specified torque of 18 lb-ft (25 Nm).
6. Remove oil filter: Unscrew the old oil filter. Be prepared for a small amount of oil to spill.
7. Install new filter: Apply a thin coat of new oil to the gasket of the new oil filter. Screw on the new filter by hand until snug, then tighten an additional 3/4 to 1 full turn.
8. Add new oil: Lower the vehicle and fill the engine with the recommended amount and type of new oil through the oil fill cap.
9. Check oil level: Start the engine and let it run for a few minutes. Turn it off, wait for a few minutes, then check the oil level with the dipstick. Add more oil if necessary.
10. Reset oil life monitor: Refer to your owner's manual for instructions on how to reset the Oil Life Monitoring system.

Common issues / tips

• 2.5L Engine: Some owners have reported excessive oil consumption in various GM Ecotec engines, including the 2.5L. Regularly check your oil level between changes and top off as needed. Using the correct Dexos-approved oil is crucial.
• Oil Filter Housing (2.5L & 2.0L Turbo): The oil filter is conveniently located at the top of the engine near the front, making it relatively easy to access for replacement.
• Drain Plug: The drain plug is typically located on the passenger side of the oil pan.
• Dexos Specification: Always use Dexos1 Gen2 (or later) approved full synthetic oil for optimal engine protection and to meet warranty requirements. This specification ensures the oil meets stringent GM standards for fuel economy, engine cleanliness, and wear protection.

Need an oil change? Find a trusted shop on Repairius.