2016 Chevrolet Tahoe Oil Capacity & Filter Reference

The 2016 Chevrolet Tahoe with the 5.3L V8 engine takes 8 quarts (7.6 liters) of SAE 0W-20 engine oil.

Quick answer

• Oil Capacity: 8 quarts (7.6 liters)
• Recommended Oil Weight: SAE 0W-20
• Oil Specification: Dexos1 Gen2 (or newer, such as Dexos1 Gen3) / API SN PLUS (or newer, such as API SP)
• Oil Filter (ACDelco): PF63F
  • Fram Cross-Reference: PH10575
  • Wix Cross-Reference: 57060
  • Mobil 1 Cross-Reference: M1-113A

Capacity by engine option

Oil change interval

Chevrolet recommends changing the engine oil and filter in your 2016 Tahoe according to the Oil Life Monitoring System. This system dynamically adjusts the interval based on driving conditions.

• Normal Duty: Typically 7,500 – 10,000 miles or 12 months, whichever comes first, as indicated by the Oil Life Monitoring System.
• Severe Duty: Under conditions such as frequent short trips, sustained idling, towing, or extreme temperatures, the system will recommend changes more frequently, potentially as low as 3,000 – 5,000 miles or 6 months.

Always adhere to the vehicle's Oil Life Monitoring System for optimal engine protection.

Drain plug torque

The oil drain plug for the 2016 Chevrolet Tahoe (5.3L V8) should be torqued to 20 ft-lbs (27 Nm). It is highly recommended to replace the drain plug gasket/crush washer with a new one each time the oil is changed to prevent leaks.

How to change the oil

1. Gather Supplies: Ensure you have the correct oil, oil filter, wrench, drain pan, and a new crush washer.
2. Warm Up Engine (optional): Briefly run the engine to warm the oil, allowing it to drain more easily.
3. Lift and Secure: Safely lift the front of the vehicle using a jack and support it with jack stands.
4. Locate Drain Plug: Place the drain pan beneath the oil pan and carefully remove the drain plug to allow the old oil to drain completely.
5. Remove Oil Filter: Once the oil has drained, remove the old oil filter. Be prepared for additional oil to drain from the filter housing.
6. Install New Filter: Apply a thin coat of new oil to the gasket of the new filter before screwing it on. Hand-tighten until snug, then an additional 3/4 to 1 full turn (or follow filter manufacturer instructions).
7. Replace Drain Plug: Install the new crush washer on the drain plug and re-install it into the oil pan. Torque to 20 ft-lbs (27 Nm).
8. Add New Oil: Lower the vehicle and fill the engine with 8 quarts of the specified SAE 0W-20 oil.
9. Check Level & Reset: Start the engine and let it run briefly, then shut off and check for leaks. Allow a few minutes for the oil to settle, then check the oil level on the dipstick and top off if necessary. Reset the Oil Life Monitoring System.

Common issues / tips

• Active Fuel Management (AFM)/Dynamic Fuel Management (DFM): The 5.3L V8 engine in this generation Tahoe features AFM. Using the correct Dexos1 Gen2 (or newer) SAE 0W-20 oil is crucial for the proper operation and longevity of AFM lifters. Using incorrect oil can contribute to lifter issues.
• Oil Consumption: Some 5.3L engines in this era can exhibit higher-than-average oil consumption. Regularly monitor your oil level between changes, especially if you drive in severe conditions.
• PCV Valve: A clogged PCV valve can contribute to oil consumption. Consider checking and replacing it if you notice excessive oil use and cannot find a leak.
• Oil Cooler Lines: Inspect oil cooler lines for leaks, especially where they connect to the radiator or engine block. These can be a common source of oil leaks as the vehicle ages.
• Oil Pressure Sensor: Failures of the oil pressure sensor are not uncommon. A faulty sensor can cause inaccurate readings or trigger a false "low oil pressure" warning.

Need an oil change? Find a trusted shop on Repairius.