2024 Toyota Highlander Oil Capacity & Filter

The 2024 Toyota Highlander takes 4.8 to 6.4 quarts of 0W-20 or 0W-16 engine oil, depending on the engine.

Quick answer

• 2.4L Turbo Engine (Gasoline Models)

  • Oil Capacity: 6.4 quarts (6.0 liters)
  • Recommended Oil Weight: 0W-20
  • Oil Type Spec: API SN PLUS or SP, or ILSAC GF-6A
  • OEM Oil Filter Part Number: 04152-YZZA8
  • Aftermarket Oil Filter Cross-References:
    • Fram: CH12674
    • Wix: WL10010
    • Mobil 1: M1C-153

• 2.5L Hybrid Engine (Hybrid Models)

  • Oil Capacity: 4.8 quarts (4.5 liters)
  • Recommended Oil Weight: 0W-16
  • Oil Type Spec: API SN PLUS or SP, or ILSAC GF-6B
  • OEM Oil Filter Part Number: 04152-YZZA6
  • Aftermarket Oil Filter Cross-References:
    • Fram: CH11677
    • Wix: WL10078
    • Mobil 1: M1C-151

Capacity by engine option

Oil change interval

Normal Duty: Toyota recommends changing the engine oil and oil filter every 10,000 miles or 12 months, whichever comes first.

Severe Duty: If you operate your 2024 Highlander under severe driving conditions, such as frequent short trips, extensive idling, towing, or driving in dusty conditions, it is recommended to change the oil and filter every 5,000 miles or 6 months.

Drain plug torque

For the 2024 Toyota Highlander, the oil drain plug torque specification is 30 ft-lbs (41 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The crush washer is typically included with a new OEM oil filter or can be purchased separately.

How to change the oil

1. Safely lift and support the front of the vehicle, or use a lift.
2. Locate the oil drain plug on the oil pan and place a drain pan underneath.
3. Remove the drain plug with the appropriate wrench and allow the oil to fully drain.
4. Locate and remove the oil filter housing (spin-on or cartridge type, depending on engine).
5. Replace the old oil filter element and O-rings with new ones. For cartridge filters, ensure the new O-rings are properly seated.
6. Install the new oil filter housing/filter, tightening to specifications (usually hand-tight plus a quarter turn or to torque spec for cartridge housings).
7. Install the drain plug with a new crush washer and torque to 30 ft-lbs (41 Nm).
8. Lower the vehicle and remove the old oil cap.
9. Fill the engine with the recommended type and amount of new engine oil through the oil fill cap opening.
10. Replace the oil fill cap, start the engine, and check for leaks. Allow the engine to reach operating temperature.
11. Turn off the engine, wait a few minutes for the oil to settle, and then check the oil level on the dipstick, adding more if necessary.
12. Reset the maintenance reminder light.

Common issues / tips

• Cartridge Filter Considerations: Both the 2.4L Turbo and 2.5L Hybrid engines on the 2024 Highlander utilize a cartridge-style oil filter. These require a specific oil filter wrench socket for removal and care when replacing the O-rings. Ensure the smaller O-ring on the filter shaft and the larger O-ring on the housing are replaced.
• Correct Oil Viscosity for Hybrids: Pay close attention to the 0W-16 oil requirement for the 2.5L Hybrid model. Using an incorrect viscosity can impact fuel economy and engine longevity.
• Turbo Engine Demands: The 2.4L turbocharged engine can be more sensitive to oil quality and change intervals. Adhering to the recommended API SN PLUS/SP or ILSAC GF-6A standards is crucial for preventing low-speed pre-ignition (LSPI) and turbocharger longevity.
• Check for Software Updates: Periodically, Toyota may release software updates that affect engine management, which can indirectly influence optimal oil performance. Consult your dealer for any outstanding service campaigns or updates.

Need an oil change? Find a trusted shop on Repairius.