2022 GMC Sierra 1500 — Oil Capacity & Filter Specs

The 2022 GMC Sierra 1500 takes between 6.0 and 8.0 quarts of oil, depending on which engine your truck is equipped with. Whether you are driving the 2.7L High-Output four-cylinder, one of the iconic EcoTec3 V8s, or the 3.0L Duramax diesel, using the correct oil specification and maintaining your fluid levels is critical to the longevity of your truck.

Below is your comprehensive guide to the oil capacity, filter part numbers, and specs for the 2022 GMC Sierra 1500.

Quick answer

Because the 5.3L V8 is the most popular engine for the 2022 Sierra 1500, the quick specs below are for the 5.3L V8 (L84). If you have a different engine, check the capacity table in the next section.

• Oil Capacity: 8.0 quarts (7.6 liters) with filter change.
• Recommended Weight: 0W-20
• Oil Specification: GM dexos1™ Gen 3 (API SP)
• OEM Oil Filter: ACDelco PF63
• Aftermarket Filters: Wix 51036 / Fram XG12060 / Mobil 1 M1-212A

Capacity by engine option

The 2022 Sierra 1500 features four main engine options (including the mid-year interior refresh models). Here are the exact oil capacities and weights for each:

Note: Always check your owner’s manual or under-hood emissions sticker to confirm your exact engine code if you are unsure.

Oil change interval

Modern GMC trucks are equipped with the GM Oil Life System (OLS), which calculates oil deterioration based on your driving habits. However, as an ASE master technician, I recommend the following general guidelines:

• Normal Duty: Change the oil and filter every 7,500 miles or 12 months, whichever comes first. Don't exceed what the Oil Life Monitor recommends.
• Severe Duty (Towing, idling, dusty roads, short trips): Change the oil and filter every 5,000 miles or 6 months.

Drain plug torque

• Torque Spec: 18 lb-ft (25 Nm) for the V8 and 2.7L engines. The 3.0L Duramax also takes 18 lb-ft.
• Crush Washer: The factory drain plug features an integrated rubber seal. While it can often be reused, inspect it for tears or flattening. If it looks worn, replace the entire drain plug or use a suitable replacement gasket to prevent slow leaks.

How to change the oil

1. Prepare the truck: Park on a level surface. If you need clearance, drive onto ramps and set the parking brake.
2. Drain the oil: Remove the oil fill cap under the hood to help the oil drain faster. Locate the oil pan and remove the 15mm drain plug. Allow the old oil to drain completely into a catch pan.
3. Replace the filter: Locate the oil filter (accessed from underneath on V8s and 2.7L engines). Use an oil filter wrench to remove it. Lubricate the new filter's rubber O-ring with fresh oil, then install it by hand. Tighten it 3/4 to 1 full turn after the gasket makes contact.
4. Reinstall drain plug: Wipe the drain plug mating surface clean, reinstall the plug, and torque it to 18 lb-ft.
5. Refill and check: Pour in the required amount of oil for your engine. Start the truck, let it run for 30 seconds to fill the filter, and shut it off. Wait a few minutes, check the dipstick, and top off if necessary.
6. Reset the monitor: Reset the Oil Life System using the steering wheel controls and the driver information center.

Common issues / tips

• Dexos Spec Upgrade: GM transitioned from dexos1 Gen 2 to dexos1 Gen 3 recently. Always look for the Gen 3 logo on the bottle for your gasoline engines. This new formulation offers better protection against Low-Speed Pre-Ignition (LSPI), which is especially important for the 2.7L Turbo engine.
• 3.0L Duramax Oil: The 3.0L diesel requires a very specific 0W-20 dexosD light-duty diesel oil. Do NOT put standard heavy-duty 15W-40 or gasoline 0W-20 in this engine, or you risk damaging the emissions systems (DPF).
• Skid Plates: If your Sierra is an AT4 or equipped with the X31 off-road package, you may have a front skid plate. You can generally reach the filter and drain plug through the access cutouts, but be prepared with a rag—oil tends to splash onto the plate and drip down slowly.

Need an oil change? Find a trusted shop on Repairius.