2016 Jeep Grand Cherokee Oil Capacity & Filter Reference Guide

The 2016 Jeep Grand Cherokee takes between 6.0 to 7.0 quarts (5.7 to 6.6 liters) of 5W-20 or 5W-30 oil, depending on the engine.

Quick Answer

• 2.4L Tigershark I4: 6.0 US Quarts (5.7 Liters) of 5W-20 API SP/SN PLUS/SN, FCA MS-6395 approved oil.
  • Oil Filter: OEM Mopar 04892339AB
  • Aftermarket Cross-Reference: Fram CH11665, Wix WL10010, Mobil 1 M1C-251A
• 3.6L Pentastar V6: 6.0 US Quarts (5.7 Liters) of 5W-20 API SP/SN PLUS/SN, FCA MS-6395 approved oil.
  • Oil Filter: OEM Mopar 04892339AB
  • Aftermarket Cross-Reference: Fram CH11665, Wix WL10010, Mobil 1 M1C-251A
• 5.7L Hemi V8: 7.0 US Quarts (6.6 Liters) of 5W-20 API SP/SN PLUS/SN, FCA MS-6395 approved oil.
  • Oil Filter: OEM Mopar 04892339AB
  • Aftermarket Cross-Reference: Fram CH11665, Wix WL10010, Mobil 1 M1C-251A
• 3.0L EcoDiesel V6: 8.0 US Quarts (7.6 Liters) of 5W-30 or 5W-40 C3 Certified Low Ash, FCA MS-11106 approved oil.
  • Oil Filter: OEM Mopar 68222952AA
  • Aftermarket Cross-Reference: Fram CH11665, Wix WL10010, Mobil 1 M1C-251A

Capacity by Engine Option

Oil Change Interval

• Normal Duty: For most drivers, an oil change is recommended every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: If you operate your Grand Cherokee under severe conditions (e.g., frequent short trips, extreme temperatures, towing, dusty roads, or heavy city traffic), an oil change is recommended every 5,000 miles or 6 months, whichever comes first.

Drain Plug Torque

• Gasoline Engines (2.4L, 3.6L, 5.7L): 20 ft-lbs (27 Nm)
• 3.0L EcoDiesel V6: 22 ft-lbs (30 Nm)

Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The crush washer helps to absorb irregularities and provides a tight seal when the drain plug is torqued.

How to Change the Oil (General Steps)

1. Warm Up Engine: Drive the vehicle for 5-10 minutes to bring the oil to operating temperature, ensuring it drains more easily.
2. Lift and Secure: Park on a level surface, engage the parking brake, and safely lift the front of the vehicle using a jack and secure it with jack stands.
3. Locate Drain Plug: Place a suitable drain pan beneath the oil pan. Locate and carefully remove the oil drain plug.
4. Drain Oil: Allow all the old oil to drain completely. This can take 10-15 minutes.
5. Replace Drain Plug: Once drained, reinstall the drain plug with a new crush washer and tighten to the specified torque.
6. Remove Oil Filter: Locate the oil filter. Use an oil filter wrench to loosen and remove the old filter. Be prepared for some oil spillage.
7. Install New Filter: Apply a thin layer of new oil to the rubber gasket of the new oil filter. Screw it on by hand until snug, then tighten an additional 3/4 to 1 full turn (or as per filter manufacturer instructions).
8. Add New Oil: Refer to the "Capacity by Engine Option" table above and add the recommended amount and type of new oil through the oil filler cap.
9. Check Level: Start the engine and let it run for a few minutes to circulate the new oil. Turn off the engine, wait a few minutes, and then check the oil level with the dipstick. Add more oil if necessary.
10. Inspect for Leaks: Visually inspect the drain plug and oil filter for any signs of leaks.

Common Issues / Tips for the 2016 Jeep Grand Cherokee (WK2 Generation)

• Oil Filter Housing (3.6L Pentastar): The oil filter housing on the 3.6L Pentastar engine (common in the WK2 generation) is made of plastic and can be prone to cracking, especially if overtightened or exposed to extreme heat cycles. Inspect the housing for leaks during oil changes.
• EcoDiesel Oil Spec: The 3.0L EcoDiesel engine requires a specific low-ash, C3-certified oil. Do not use conventional gasoline engine oils as this can lead to premature DPF (Diesel Particulate Filter) clogging and damage.
• Hemi MDS System: The 5.7L Hemi engine utilizes a Multi-Displacement System (MDS) that relies on proper oil viscosity and pressure. Using the incorrect oil weight or extending oil change intervals can potentially lead to issues with the MDS lifters.
• Oil Consumption (some units): While not widespread, some 3.6L Pentastar engines have reported minor oil consumption. Regularly checking your oil level between changes is good practice.

Need an oil change? Find a trusted shop on Repairius.