2014 Nissan Titan Torque Specifications
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2014 Nissan Titan? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Quick Reference
| Fastener | Torque (ft-lb / Nm) | Notes |
|---|---|---|
| Wheel Lug Nuts | 98-110 ft-lb / 133-149 Nm | Be sure to retorque after 50-100 miles. |
| Oil Drain Plug | 25 ft-lb / 34 Nm | Always use a new crush washer. |
| Transmission Drain Plug | 25 ft-lb / 34 Nm | |
| Front Brake Caliper Bracket Bolts | 129 ft-lb / 175 Nm | |
| Front Brake Caliper Slide Pins | 40 ft-lb / 54 Nm | |
| Rear Brake Caliper Bracket Bolts | 70 ft-lb / 95 Nm | |
| Rear Brake Caliper Slide Pins | 18 ft-lb / 24 Nm | |
| Axle Nut | 129 ft-lb / 175 Nm | Use a new cotter pin. |
| Spark Plugs | 20 ft-lb / 27 Nm | Use a torque wrench with an extension and a magnetic socket. |
| Valve Cover Bolts | 80 in-lb / 9 Nm | Tighten in the specified sequence to avoid warping the cover. |
| Intake Manifold Bolts | 8 ft-lb / 11 Nm |
Wheel Lug Torque Pattern
When tightening the lug nuts on your 2014 Nissan Titan, it is crucial to use a star or cross pattern. This ensures that the wheel is seated evenly against the hub, preventing vibration and potential damage. Never tighten lug nuts in a circular pattern.
Start by snugging all the lug nuts down by hand. Then, using a calibrated torque wrench, tighten them in a star pattern to half the specified torque. Finally, repeat the star pattern, bringing each lug nut to its final torque value of 98-110 ft-lb (133-149 Nm).
Brake Torque Notes
Properly torquing your brake components is a critical safety measure. For the 2014 Nissan Titan, pay close attention to the difference in torque between the front and rear axle, as well as the caliper bracket bolts versus the slide pins. The large caliper bracket bolts require a significantly higher torque value as they are responsible for holding the entire brake caliper assembly to the knuckle. The smaller slide pins require much less torque; over-tightening them can prevent the caliper from moving freely, leading to uneven pad wear and braking problems.
Always use a high-quality, calibrated torque wrench for these components. We recommend cleaning the threads and using a thread-locking compound on the caliper bracket bolts as an added safety precaution.
Why Torque Matters
Using a torque wrench is not just for professional technicians. It's a vital step for any DIY repair to ensure the safety, reliability, and longevity of your vehicle. A fastener that is too loose can vibrate free, leading to catastrophic failure. A fastener that is too tight can stretch, weaken, or break, or it can damage the part it is holding. For example, over-tightening a valve cover can warp the cover and cause an oil leak. Over-tightening a spark plug can damage the threads in the cylinder head, a very costly repair.
Investing in a quality torque wrench and using the correct specifications for your 2014 Nissan Titan is one of the smartest things you can do to protect your truck and ensure your repairs are done right.
Disclaimer: The torque specifications listed above are for reference only. For critical fasteners, it is always recommended to consult the official OEM service manual for your specific vehicle configuration.
Find a trusted shop on Repairius.
More specs for the 2014 Nissan Titan
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2014 Nissan Titan Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.