2024 Toyota Camry Oil Capacity & Filter

The 2024 Toyota Camry takes between 4.5 quarts (4.3 Liters) and 5.1 quarts (4.8 Liters) of engine oil, depending on the engine configuration.

Quick Answer

• 2.5L 4-Cylinder Engine (A25A-FKS):

  • Oil Capacity: 4.8 US Quarts (4.5 Liters) with filter
  • Recommended Oil Weight: 0W-16
  • Oil Specification: API SP / ILSAC GF-6B
  • OEM Oil Filter Part Number: 04152-YZZA6
  • Aftermarket Oil Filter Cross-References:
    • Fram: CH12128
    • Wix: WL10010
    • Mobil 1: M1C-153A

• 3.5L V6 Engine (2GR-FKS):

  • Oil Capacity: 4.5 US Quarts (4.3 Liters) with filter
  • Recommended Oil Weight: 0W-20
  • Oil Specification: API SP / ILSAC GF-6A
  • OEM Oil Filter Part Number: 04152-YZZA6
  • Aftermarket Oil Filter Cross-References:
    • Fram: CH12128
    • Wix: WL10010
    • Mobil 1: M1C-153A

Capacity by Engine Option

Oil Change Interval

Toyota recommends the following oil change intervals for the 2024 Camry:

• Normal Driving Conditions: Every 10,000 miles or 12 months, whichever comes first.
• Severe Driving Conditions: Every 5,000 miles or 6 months, whichever comes first. Severe conditions include frequent short trips, towing, extensive idling, or driving in dusty conditions.

Always refer to your vehicle's owner's manual for the most accurate and up-to-date maintenance schedule.

Drain Plug Torque

The oil drain plug torque specification for both the 2.5L 4-cylinder and 3.5L V6 engines in the 2024 Toyota Camry is 30 ft-lbs (41 Nm).

Always use a new crush washer when performing an oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is typically 90430-12031, but it is always best to confirm with your dealer or parts supplier.

How to Change the Oil

1. Gather Supplies: Ensure you have the correct oil, oil filter, drain pan, wrench, torque wrench, and a new crush washer.
2. Warm Up Engine (Optional but Recommended): Drive the car for a few minutes to warm the oil, allowing it to drain more easily.
3. Lift and Secure Vehicle: Safely lift the front of the vehicle using a jack and secure it with jack stands.
4. Locate Drain Plug: Place the drain pan directly under the oil drain plug, which is typically located on the bottom of the oil pan.
5. Drain Oil: Carefully remove the drain plug (counter-clockwise) and allow all the old oil to drain completely. Inspect the old crush washer.
6. Replace Drain Plug: Install a new crush washer on the drain plug and reinsert it into the oil pan. Torque to 30 ft-lbs (41 Nm).
7. Remove Old Oil Filter: Locate the oil filter (often near the front of the engine, sometimes under a cover). Use an oil filter wrench to remove it counter-clockwise. Be prepared for a small amount of oil to spill.
8. Prepare New Oil Filter: Apply a thin film of new engine oil to the rubber gasket of the new oil filter.
9. Install New Oil Filter: Screw on the new oil filter by hand until snug, then tighten an additional 3/4 to 1 full turn (or as per filter manufacturer's instructions).
10. Add New Oil: Carefully pour the recommended amount and type of new engine oil into the engine's oil fill cap.
11. Check Oil Level: Start the engine and let it run for a few minutes. Turn it off, wait for the oil to settle, then check the oil level on the dipstick. Add more oil if necessary.
12. Dispose of Old Oil: Properly dispose of the used oil and filter at an authorized recycling center.

Common Issues / Tips (XV70 Generation 2018-Present)

• Oil Filter Housing: The 2.5L 4-cylinder and 3.5L V6 engines often utilize a cartridge-style oil filter within a plastic housing. Be careful not to overtighten the housing during reinstallation, as this can lead to cracks or leaks. The torque specification for the oil filter housing cap is typically 18 ft-lbs (25 Nm) and a new O-ring should always be used. Many aftermarket filters will come with a new O-ring.
• 0W-16 Oil for 2.5L: The 2.5L engine specifically requires 0W-16 oil, which is a lower viscosity oil designed for improved fuel efficiency. Using an incorrect weight of oil, such as 0W-20, could potentially impact fuel economy and engine longevity. Always adhere to the recommended oil viscosity.
• Underbody Cover: The 2024 Camry has an underbody splash shield that needs to be removed to access the oil drain plug and filter. This typically involves removing several clips and/or bolts. Ensure all fasteners are reinstalled correctly to prevent the cover from sagging or falling off.
• Hybrid Models: While this article focuses on gasoline-only models, hybrid Camry models (also with the 2.5L engine) will have similar oil capacity and specifications, but always double-check your specific owner's manual for confirmation.

Need an oil change? Find a trusted shop on Repairius.