2019 Chevrolet Silverado 1500 Oil Capacity & Filter Guide

The 2019 Chevrolet Silverado 1500 requires between 6.0 and 8.0 quarts of oil, depending on the engine. For a precise measurement, always consult your owner's manual and check the dipstick after refilling.

Quick Answer: 2019 Silverado Oil Specs

Here are the essential specifications for a standard oil change on the most common 2019 Silverado 1500 engines. Note that the V8 and V6 engines use a traditional spin-on filter, while the 4-cylinder and diesel engines use a cartridge-style filter.

• 5.3L & 6.2L V8 Engines:

  • Oil Capacity: 8.0 quarts / 7.6 liters with filter.
  • Recommended Oil Weight: SAE 0W-20
  • Oil Specification: Must meet dexos1® Gen 2 (or newer) specification.
  • OEM Oil Filter: ACDelco PF63E
  • Aftermarket Filters: Fram PH10575, Wix WL10255, Mobil 1 M1-212A.

• 2.7L Turbo L3B Engine:

  • Oil Capacity: 6.0 quarts / 5.7 liters with filter.
  • Recommended Oil Weight: SAE 5W-30
  • Oil Specification: Must meet dexos1® Gen 2 (or newer) specification.
  • OEM Oil Filter: ACDelco PF66
  • Aftermarket Filters: Fram CH12246, Wix WL10331, Mobil 1 M1C-458A.

Capacity by Engine Option

The 2019 model year offered a wide range of engines, each with specific oil requirements. It is critical to use the correct oil type and viscosity to protect advanced engine technologies like Dynamic Fuel Management (DFM) and turbochargers.

Note: The 3.0L Duramax diesel requires a special dexosD® specification oil, which is different from the dexos1® used in the gasoline engines. Using the wrong oil can damage the diesel particulate filter (DPF) and other emissions components.

Oil Change Interval

Your 2019 Silverado is equipped with an Oil Life Monitoring (OLM) system. The dashboard will display a "Change Engine Oil Soon" message when it's time for a service. This system is the most accurate guide, as it tracks mileage, engine temperature, and operating conditions.

• Normal Duty: The OLM will typically recommend an oil change every 7,500 to 10,000 miles, or once per year, whichever comes first.
• Severe Duty: If you frequently tow heavy loads, operate in extreme temperatures, idle for long periods, or drive in dusty off-road conditions, the OLM will adjust accordingly, often recommending an interval between 3,000 and 5,000 miles.

Drain Plug Torque

Properly tightening the oil drain plug prevents leaks without stripping the threads in the aluminum oil pan.

• Drain Plug Torque: 18 lb-ft (25 N·m)
• Drain Plug Socket Size: 15mm Hex

Crush Washer Note: The factory drain plug typically has an integrated rubber or metal gasket. Inspect it for tears or flattening at every oil change. It is best practice to replace the drain plug (GM Part # 11562588 or similar) every few services to ensure a perfect seal.

How to Change the Oil

1. Run the engine for 2-3 minutes to warm the oil, then shut it off.
2. Place a drain pan under the oil pan, remove the 15mm drain plug, and let the oil drain completely.
3. Locate and remove the oil filter. For V6/V8 engines, this is a spin-on canister. For 2.7L/3.0L engines, this is a cartridge filter inside a plastic housing.
4. Wipe the filter mounting surface clean. Lightly lubricate the new filter's gasket with fresh oil.
5. Install the new filter. Spin-on filters should be hand-tightened one full turn after the gasket makes contact. Cartridge filter housing torque is typically marked on the cap (usually 18 lb-ft).
6. Reinstall the oil drain plug and torque to 18 lb-ft.
7. Refill the engine with the correct amount and type of oil through the oil fill cap on the valve cover.
8. Start the engine, let it run for 30 seconds, then shut it off. Wait a minute for the oil to settle, then check the dipstick and top off as needed.
9. Reset the Oil Life Monitor through the infotainment screen or driver information center.

Common Issues / Tips

• V8 Oil Consumption: Some 5.3L and 6.2L V8s with Dynamic Fuel Management (DFM) can consume oil. Using only dexos1 Gen 2 certified 0W-20 synthetic oil is critical for the proper function of the complex DFM lifters. Check your oil level every 1,000 miles.
• Cartridge Filter O-Rings: When changing the oil on a 2.7L or 3.0L engine, always replace the o-rings on the filter cap. The new filter will include them. Lubricate them with fresh oil to prevent tearing.
• Increased V8 Capacity: The 8.0-quart capacity for the V8s is a notable increase from the previous generation's 6.0 quarts. Double-check that you have purchased enough oil before starting the job.

Need an oil change? Find a trusted shop on Repairius.