2025 Honda Pilot Oil Capacity & Filter Specs

The 2025 Honda Pilot takes 5.7 US quarts (5.4 liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 5.7 US quarts (5.4 liters)
• Recommended Oil Weight: 0W-20
• Oil Type Spec: API Premium Grade Drained-Engine Oil, or API Certification Seal with "Resource Conserving," or Honda's HTO-06 specification.
• OEM Oil Filter Part Number: 15400-PLM-A02 or 15400-RTA-003 (Always consult your Honda dealer for the most accurate part number for your specific VIN)
• Aftermarket Oil Filter Cross-References:
  • Fram: PH7317
  • Wix: 51356
  • Mobil 1: M1-110

Capacity by Engine Option

For the 2025 Honda Pilot, all trims are equipped with the same 3.5L V6 engine. Therefore, the oil capacity remains consistent across the board.

Oil Change Interval

Honda recommends following the Maintenance Minder system displayed on your dashboard. This system dynamically calculates the oil life based on your driving conditions.

• Normal Duty: Typically, the Maintenance Minder will indicate an oil change is due between 7,500 and 10,000 miles, or every 12 months, whichever comes first.
• Severe Duty: If you frequently drive in severe conditions (e.g., extreme temperatures, dusty environments, heavy city traffic, towing, or short trips), the Maintenance Minder will likely recommend more frequent oil changes, possibly as often as every 3,000 to 5,000 miles. Always refer to your vehicle's Maintenance Minder for precise intervals.

Drain Plug Torque

The oil drain plug for the 2025 Honda Pilot should be torqued to 29 lb-ft (39 N·m). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is typically 94109-14000, but confirm with your dealer for the most accurate information for your specific model year.

How to Change the Oil

1. Gather Supplies: New oil, oil filter, drain pan, wrench for drain plug, oil filter wrench, funnel, new crush washer, jack and jack stands (if needed), safety glasses, and gloves.
2. Warm Up Engine (Slightly): Run the engine for a few minutes to warm the oil, allowing it to drain more easily. Do not make it hot.
3. Lift and Secure Vehicle: Safely raise the front of the vehicle using a jack and support it with jack stands on a level surface.
4. Locate Drain Plug: Find the oil drain plug on the oil pan, usually at the bottom rear of the engine.
5. Drain Oil: Place the drain pan underneath and carefully remove the drain plug. Allow all the old oil to drain completely.
6. Replace Drain Plug: Install a new crush washer on the drain plug and re-install it, tightening to 29 lb-ft (39 N·m).
7. Remove Oil Filter: Locate the oil filter (usually on the front or side of the engine block). Use an oil filter wrench to remove it. Be prepared for some oil spillage.
8. Prepare New Filter: Apply a thin film of new oil to the rubber gasket of the new oil filter.
9. Install New Filter: Hand-tighten the new oil filter until snug, then turn an additional 3/4 to 1 full turn. Consult the filter packaging for specific instructions.
10. Add New Oil: Using a funnel, add 5.7 US quarts of 0W-20 engine oil.
11. Check Level: Start the engine and let it run for a few minutes. Turn it off, wait a few minutes for the oil to settle, and then check the dipstick. Add more oil if necessary.
12. Check for Leaks: Inspect the drain plug and oil filter area for any signs of leaks.
13. Reset Maintenance Minder: Follow your owner's manual instructions to reset the oil life monitor.

Common Issues / Tips

• VCM (Variable Cylinder Management): The 3.5L V6 engine in the Pilot utilizes Honda's Variable Cylinder Management. While Honda has made improvements over the years, some earlier generations experienced increased oil consumption due to VCM. Using the correct 0W-20 oil and adhering to oil change intervals is crucial. Monitor your oil level between changes, especially if you notice increased consumption.
• Maintenance Minder Accuracy: Trust the Maintenance Minder system. It