2024 Jeep Cherokee — Torque Specifications
Quick-reference torques for wheels, brakes, engine, and drivetrain fasteners
Working on this 2024 Jeep Cherokee? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Quick answer — 2024 Jeep Cherokee
- Wheel lug nuts
- 95–110 ft-lb (129–149 Nm)
- Engine oil drain plug
- 20–30 ft-lb (27–41 Nm)
- Transmission drain plug (9-speed 948TE, if equipped)
- 13–30 ft-lb (18–41 Nm)
- Front brake caliper bracket bolts
- 90–105 ft-lb (122–142 Nm)
From the table below. Confirm with your owner's manual for your exact engine.
Quick reference
| Fastener | Torque (ft-lb / Nm) | Notes |
|---|---|---|
| Wheel lug nuts | 95–110 ft-lb (129–149 Nm) | 5-lug KL platform; torque in a star pattern in 2–3 passes |
| Engine oil drain plug | 20–30 ft-lb (27–41 Nm) | Verify plug/washer style; do not overtighten aluminum pans |
| Transmission drain plug (9-speed 948TE, if equipped) | 13–30 ft-lb (18–41 Nm) | Some pans have no drain; verify by VIN. Pan bolts typically 7–9 ft-lb (10–12 Nm) if serviced |
| Front brake caliper bracket bolts | 90–105 ft-lb (122–142 Nm) | Varies with rotor size/trim (e.g., Trailhawk vs. Latitude) |
| Rear brake caliper bracket bolts | 74–90 ft-lb (100–122 Nm) | Solid vs. vented rotor packages differ |
| Brake caliper slide pins (front/rear) | 20–28 ft-lb (27–38 Nm) | Clean and lube pins with high-temp silicone/PTFE brake grease |
| Front axle/hub nut | 150–180 ft-lb (203–244 Nm) | Replace staked nut; torque with wheel braked; no final impact torquing |
| Spark plugs (gas engines) | 13–22 ft-lb (18–30 Nm) | 2.0T/3.2L ranges; gasket vs. taper seat affects torque; start by hand |
| Glow plugs (diesel, if equipped) | 11–15 ft-lb (15–20 Nm) | Not common for 2024 U.S. models—verify engine |
| Valve cover bolts | 7–9 ft-lb (10–12 Nm) | Tighten in sequence in two stages |
| Intake manifold bolts | 7–9 ft-lb (10–12 Nm) | Center-out pattern, two stages |
Wheel lug torque pattern
The 2024 Jeep Cherokee uses a 5-lug hub. Always tighten the lug nuts in a star (crisscross) pattern to ensure the wheel centers properly on the hub and the rotor seats squarely against the hub face. Best practice:
- Snug all five nuts by hand with the wheel off the ground.
- Torque to half-spec in a star pattern.
- Finish to final spec (95–110 ft-lb) in the same star pattern.
- Recheck torque after 25–50 miles whenever a wheel has been off the vehicle or after new wheel installations.
Brake torque notes
- Caliper bracket bolts: Cherokee packages vary by trim, rotor size, and whether the vehicle is equipped with tow/off-road packages. Use the ranges above (front 90–105 ft-lb, rear 74–90 ft-lb) and verify for your exact VIN. Clean the knuckle and bracket threads; apply threadlocker only if directed by the service manual.
- Caliper slide pins: 20–28 ft-lb is typical. Remove rust and old grease, and use a high-temp silicone or PTFE-based brake lubricant. Ensure the correct pin boots are installed and seated.
- Rotor retention: If your rotor uses a small retaining screw, tighten only to light hand torque; it is not a structural fastener.
- Hub/axle nut: Replace the staked nut any time it’s removed. Have an assistant apply the brakes or use a hub holding tool, then torque to 150–180 ft-lb. Do not back off the nut to align a cotter pin (if used) and do not use an impact for the final torque—bearing life depends on proper preload.
Engine and drivetrain notes
- Oil drain plug: Use a new crush washer if equipped. Aluminum pans are sensitive to over-torque; 20–30 ft-lb is adequate in most cases. Wipe the sealing surface clean before installation.
- Transmission service (948TE 9-speed): Some Cherokees have a pan drain; others require pan removal to drain. If your pan has a drain, torque is commonly in the 13–30 ft-lb range. Pan perimeter bolts typically tighten to 7–9 ft-lb (10–12 Nm) in a crisscross pattern—do not overtighten the thin pan flange. Always verify fluid temperature and level set procedures per OEM.
- Spark plugs: Many Cherokee engines use long-reach, gasketed plugs. Torque falls in the 13–22 ft-lb range depending on thread size and plug design. If anti-seize is used (often not recommended by plug makers), reduce torque and follow the spark plug manufacturer’s guidance. Always start plugs by hand to avoid cross-threading, and tighten on a cold engine.
- Valve cover and intake manifold: Both use low torque (7–9 ft-lb). Tighten in sequence, in two to three passes, to prevent warping and oil/vacuum leaks. Replace any rubber grommets or molded seals that are flattened or hardened.
Why torque matters
Applying the correct torque keeps fasteners clamped without distortion or damage. Over-torqued wheel nuts can stretch studs, warp rotors, and make roadside removal impossible; under-torqued nuts can loosen and cause vibration or wheel loss. Brake bracket bolts set caliper alignment and resist severe brake loads—too loose can cause noise and pad taper, too tight can damage threads. Axle nut preload directly impacts wheel bearing life. Engine fasteners like spark plugs, valve covers, and intake manifolds seal combustion, oil, and vacuum—incorrect torque leads to misfires, leaks, and drivability issues.
Disclaimer: Torque values above are typical ranges compiled for the 2024 Jeep Cherokee family and may vary by engine, trim, brake package, and market. Critical fasteners should always be verified against the OEM service manual for your exact VIN.
Find a trusted shop on Repairius.
Need service on your Jeep Cherokee?
Your vehicle and question are already filled in — just add your location.
More specs for the 2024 Jeep Cherokee
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2024 Jeep Cherokee Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.
Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-10-08.