2025 Jeep Wrangler Paint Codes

Quick reference

Where to find your paint code

Locating the paint code on your 2025 Jeep Wrangler is straightforward. The most common location is on a sticker attached to the driver's side door jamb or the B-pillar (the vertical support between the front and rear doors). This sticker typically contains various vehicle information, including a barcode and a section dedicated to paint codes. Look for a label that says "PAINT" or "EXT PNT" followed by a two or three-character code, which may also include a letter indicating the paint type (e.g., C for clear coat). In some cases, the paint code might also be found under the hood, often on a sticker affixed to the radiator support or firewall.

If you have difficulty finding the paint code, your local Jeep dealership parts department can provide it using your Vehicle Identification Number (VIN). Alternatively, online VIN decoders or paint supplier websites can also help you pinpoint the correct code.

Best touch-up paint sources

When it comes to touching up minor scratches or chips on your 2025 Jeep Wrangler, several reputable sources offer quality paint matches:

• Dupli-Color: Widely available at automotive parts stores, Dupli-Color provides aerosol cans, paint pens, and brush-in bottles. They offer a good selection of factory-matched colors.
• AutomotiveTouchup: This online retailer specializes in custom-mixed touch-up paint that is formulated to precisely match your vehicle's factory color. They offer a wider range of application options, including pens, bottles, and aerosol cans, and are known for their accurate color matching.
• Tcoat Custom-Mix: For a truly custom and precise match, Tcoat can create a paint mixture based on your vehicle's specific paint code, often resulting in a superior blend, especially for metallic and pearl finishes.
• Dealership: Your local Jeep dealership can also provide genuine OEM touch-up paint. While sometimes more expensive, it guarantees an exact factory match.

How to use touch-up paint

Achieving a seamless repair with touch-up paint requires a few careful steps:

1. Clean the area: Thoroughly clean the chipped or scratched area with soap and water, then follow with a wax and grease remover to ensure proper adhesion.
2. Apply primer (optional but recommended): For deeper chips that expose bare metal, apply a thin layer of primer and allow it to dry completely. This promotes adhesion and prevents rust.
3. Apply base coat: Apply several thin coats of your base color, allowing each coat to dry for the recommended time before applying the next. Build up the paint gradually until the chip is filled and the color matches the surrounding area. Avoid applying too much paint at once, as this can lead to an uneven finish.
4. Apply clear coat: Once the base coat is dry, apply two to three thin coats of clear coat to protect the paint and provide a glossy finish. Allow sufficient drying time between coats and for the final clear coat.
5. Wet sand and polish (optional): For a truly professional finish, after the clear coat has fully cured (24-48 hours), you can carefully wet sand the area with very fine-grit sandpaper (e.g., 2000-3000 grit) and then polish it to a smooth, factory-like shine.

Color matching tips for pearls and tri-coats

Pearl and tri-coat paints, which contain microscopic metallic or mica particles, can be more challenging to match perfectly due to their multi-layered nature and the way light interacts with them. Here are some tips:

• Professional color matching: For these complex finishes, consider using a custom-mix service like Tcoat that can take into account the various layers and nuances of your paint.
• Test on an inconspicuous area: Before applying to the damaged spot, always test the touch-up paint on an unseen area (like inside the fuel door) to ensure the color match is satisfactory.
• Apply in thin layers: When applying the pearl or mid-coat layer, thinner coats are crucial to controlling the depth and shimmer of the color.
• Angle of application: The angle at which you apply the paint, especially with aerosol cans, can affect the metallic or pearl flake orientation, subtly altering the final appearance. Experiment with different angles on a test patch.

Find a trusted body shop on Repairius.