Working on this vehicle? Write estimates, send inspections & invoice customers from your phone.

    Start 14-Day Free Trial
    ← All vehicle specs
    Coolant Capacity & Type

    2019 Nissan Frontier Coolant Capacity & Type

    AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.

    Working on this 2019 Nissan Frontier? Run just this one job through Repairius.

    No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.

    14-day free trial · credit card required · cancel anytime

    The 2019 Nissan Frontier cooling system typically holds between 9.0 to 10.0 quarts (8.5 to 9.5 liters) of coolant, depending on the engine and configuration.

    Quick Answer

    • Total Cooling System Capacity: 9.0 - 10.0 quarts (8.5 - 9.5 liters)
    • OEM Coolant Spec: Nissan Genuine Long Life Antifreeze/Coolant, Blue, Phosphate Hybrid Organic Acid Technology (P-HOAT), Nissan L250 (or equivalent).
    • Mix Ratio: 50/50 pre-mix or 50% concentrate with 50% distilled water.

    Capacity by Engine Option

    The 2019 Nissan Frontier was offered with two engine options, and their cooling system capacities are slightly different:

    • 2.5L I4 Engine: Approximately 9.0 quarts (8.5 liters)
    • 4.0L V6 Engine: Approximately 10.0 quarts (9.5 liters)

    Always consult your owner's manual for the most precise capacity figures for your specific vehicle configuration.

    Flush Interval

    Maintaining the correct coolant and ensuring it's fresh is crucial for the longevity of your cooling system components.

    • Normal Duty: Replace every 60,000 miles or 48 months, whichever comes first.
    • Severe Duty: Consider replacing every 30,000 miles or 24 months, especially if you regularly tow, drive in extreme temperatures, or operate in dusty conditions.

    Refer to your Nissan Frontier's owner's manual for the factory-recommended maintenance schedule.

    How to Refill & Bleed

    Properly refilling and bleeding the cooling system is vital to prevent air pockets, which can lead to overheating. Here's a general procedure:

    1. Safety First: Ensure the engine is completely cool before starting.
    2. Drain Old Coolant: With the engine off and cool, open the radiator drain cock (petcock) located at the bottom of the radiator. Remove the radiator cap to speed up draining. Catch the old coolant in a suitable container for proper disposal.
    3. Flush (Optional but Recommended): If desired, flush the system with distilled water until clear water flows out. You can use a dedicated coolant flush product as directed.
    4. Close Drain: Once drained, close the radiator drain cock securely.
    5. Refill: Begin filling the radiator with the specified Nissan genuine blue P-HOAT 50/50 coolant mix. Fill slowly to allow air to escape.
    6. Fill Reservoir: Fill the coolant reservoir (expansion tank) to the "MAX" or "FULL" line.
    7. Bleed Air:
      • Start the engine and let it run with the heater on full blast (hot). This will open the heater core valve and help circulate coolant.
      • As the engine warms up, coolant levels in the radiator and reservoir may drop. Continuously top off the radiator until it remains full.
      • Many Nissan Frontier models have a small air bleed screw near the thermostat housing or on the upper radiator hose. Open this screw slightly until a steady stream of coolant (without air bubbles) emerges, then close it.
      • Squeeze the upper and lower radiator hoses several times to help dislodge air bubbles.
      • Continue running the engine until the thermostat opens (you

    Need service on your Nissan Frontier?

    Request service from shops in your area.

    More specs for the 2019 Nissan Frontier

    Oil Capacity & Filter

    Capacity, weight, filter PN, drain plug torque, change interval.

    Fluid Type Specs

    Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.

    Transmission Fluid & Service

    Trans model, fluid spec, capacity, filter PN, service interval.

    Torque Specifications

    Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.

    Brake Pad & Rotor Specs

    Pad PNs, rotor size, min thickness, caliper torque.

    Tire Size & Pressure

    OEM size, cold psi, bolt pattern, wheel size, TPMS.

    Battery Size & Group

    Group size, CCA, AGM/flooded, dimensions, reset note.

    A/C Refrigerant & Oil

    R-134a or R-1234yf, charge oz, PAG oil spec.

    Bulb Sizes (Headlight, Tail, Fog)

    Headlight, fog, tail, turn, reverse, interior.

    Factory Maintenance Schedule

    Service intervals by mileage, severe-duty notes, known issues.

    Towing Capacity & Payload

    Max tow, payload, GVWR/GCWR, hitch class by trim.

    Fuse Box Diagram & Amperage

    Fuse box locations, layout, amps, and what each fuse controls.

    Serpentine Belt Routing & Length

    Belt routing, length, rib count, OEM + aftermarket PNs.

    Wheel Alignment Specifications

    Camber, caster, toe ranges (front & rear), adjustability notes.

    Paint Color Codes

    All factory colors with paint codes, sticker location, touch-up tips.

    Wiper Blade Sizes

    Driver/passenger/rear blade size, attachment, OEM + cross-refs.

    Spark Plug Type & Gap

    Plug PN, gap, torque, interval by engine.

    Transmission & Axle Gear Ratios

    Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.

    Key Fob Programming

    DIY programming steps, FCC ID, fob PN, battery, transponder.

    Same spec — other model years

    Maintenance & repair guides

    Browse by make

    Running an auto or diesel repair shop?

    Compare Repairius to the shop software you're paying for

    $99.99/month (first location included), unlimited users, 14-day free trial.

    Run your shop from estimate to payment

    Don't overhaul your shop. Test Repairius on your next job.

    Repairius keeps estimates, work orders, real-time job assignment, customer and vehicle history, inventory, and payments in one place — on desktop and in your pocket.

    14-day free trial · credit card required · cancel anytime

    Not a mechanic? Send Repairius to your shop — they can run estimates, jobs, and invoices in one place.

    Know someone who needs this?

    Share this page with a mechanic, a shop owner, or a friend working on the same problem.

    Know a mechanic or shop owner Repairius could help?

    Send them Repairius in one tap. Free listing, online booking, reminders and the full shop workflow.

    Text them Email