Working on this vehicle? Write estimates, send inspections & invoice customers from your phone.

    Start 14-Day Free Trial
    ← All vehicle specs
    Serpentine Belt Routing & Length

    2023 Ram ProMaster Serpentine Belt Routing & Length

    Working on this 2023 Ram ProMaster? Run just this one job through Repairius.

    No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.

    14-day free trial · credit card required · cancel anytime

    2023 Ram ProMaster factory oil capacity

    EngineCapacityOilFilter
    3.6L6 qt (5.6 L)SAE 0W-20 (first grade listed; see chart)—

    Source: Mopar StarParts vehicle fluid specifications (FCA US LLC / Stellantis). Values as printed. Oil capacity finder →

    Quick Answer

    • Belt Length: 2100mm (82.7 inches)
    • Rib Count: 6-rib
    • OEM Belt PN: 68522304AA
    • Aftermarket Cross-references:
      • Gates K060827
      • Dayco 5060827
      • Continental Elite 4060827
    • Auto-Tensioner PN: 68522305AA
    • Idler Pulley PN: 68522306AA

    Belt Routing

    The 2023 Ram ProMaster, equipped with the 3.6L Pentastar V6 engine, features a single serpentine belt that drives all the essential accessories. Before you even think about removing the old belt, it is highly recommended to take a clear photograph of the current belt routing. This will serve as an invaluable reference during reinstallation.

    Here's a step-by-step description of the belt's path:

    1. Crankshaft Pulley: Begin at the lowest point of the engine, the main crankshaft pulley. The belt comes off the top of this pulley.
    2. A/C Compressor: From the crankshaft, the belt travels upwards to the air conditioning (A/C) compressor pulley, usually located on the lower passenger side of the engine. The belt will wrap around the top of this pulley.
    3. Idler Pulley: Next, the belt goes to the first idler pulley, which helps guide the belt and maintain tension. This idler is typically above and slightly to the inside of the A/C compressor.
    4. Alternator: Continuing its upward path, the belt then wraps around the alternator pulley, positioned higher on the passenger side of the engine.
    5. Power Steering Pump: From the alternator, the belt crosses over to the power steering pump pulley, generally located on the upper driver's side of the engine.
    6. Water Pump: After the power steering pump, the belt proceeds to the water pump pulley, which is typically found in the center-top area of the engine, below the tensioner.
    7. Tensioner: Finally, the belt goes around the ribbed surface of the automatic tensioner pulley, located on the upper driver's side, slightly above the power steering pump. The tensioner maintains constant pressure on the belt.

    How to Replace the Serpentine Belt

    Replacing the serpentine belt on your 2023 Ram ProMaster requires a bit of mechanical know-how, but it's a manageable DIY task for many. You will need a serpentine belt tool or a long 3/8-inch drive breaker bar to release the tension on the automatic tensioner.

    1. Locate the Automatic Tensioner: Identify the automatic tensioner pulley. It will have a square opening for your tool.
    2. Relieve Tension: Insert your serpentine belt tool or breaker bar into the square opening on the tensioner. Rotate the tool clockwise (or counter-clockwise, depending on the tensioner design – you'll feel it move) to release the tension on the belt. Hold it in this position.
    3. Remove the Old Belt: While holding the tensioner open, carefully slip the old belt off one of the pulleys, usually the idler pulley or the alternator, to start.
    4. Inspect Pulleys: With the belt off, take this opportunity to inspect all the pulleys (alternator, A/C compressor, power steering, water pump, idler, tensioner) for any signs of wear, wobbling, or noise when spun by hand. Replace any faulty pulleys.
    5. Route the New Belt: Referring to your photograph or the "Belt Routing" section above, carefully route the new belt around all the pulleys, leaving the tensioner pulley (or another easily accessible pulley) as the last one to be installed.
    6. Install on Tensioner: Apply pressure to the tensioner again with your tool and slip the new belt fully onto the final pulley.
    7. Release Tensioner: Slowly release the tensioner, ensuring the belt is seated correctly in all the grooves of all the pulleys.
    8. Double-Check: Start the engine briefly and observe the belt to ensure it's tracking correctly and there are no abnormal noises. Turn the engine off and re-check the belt path.

    Replacement Interval

    While there is no universally fixed replacement interval for serpentine belts, a good general guideline for the 2023 Ram ProMaster's 3.6L Pentastar V6 is to inspect it regularly and consider replacement every 60,000 to 100,000 miles, or every 5-7 years, whichever comes first. However, driving conditions and climate can affect belt life. It's crucial to inspect your belt for signs of wear during routine maintenance.

    Signs of a Failing Belt or Tensioner

    Ignoring a failing serpentine belt or tensioner can lead to serious issues, including loss of power steering, A/C, and charging system, potentially leaving you stranded. Be aware of these warning signs:

    • Squealing or Chirping Noises: This is often the most common symptom, especially during cold starts or when turning the steering wheel (indicating power steering strain). It can be caused by a worn belt, misaligned pulley, or a failing tensioner.
    • Cracks, Fraying, or Glazing on the Belt: Visually inspect the belt. Deep cracks, missing chunks of rubber, fraying along the edges, or a shiny, glazed appearance on the ribbed side indicate accelerated wear and a need for replacement.
    • Loss of Accessory Function: If your A/C stops blowing cold, your power steering becomes difficult to turn, or your battery light comes on (indicating the alternator isn't charging), it could be due to a slipping or broken serpentine belt.
    • Vibrations or Wobbling from Pulleys: A failing tensioner or idler pulley might exhibit excessive vibration or wobbling while the engine is running. This can lead to premature belt wear.
    • Visible Wear on the Tensioner or Idler Pulley: Inspect the tensioner arm for excessive play. If the tensioner or idler pulley feels rough when spun by hand or makes noise, it's time for replacement.

    Find a trusted shop on Repairius.

    Need service on your Ram ProMaster?

    Your vehicle and question are already filled in — just add your location.

    More specs for the 2023 Ram ProMaster

    Oil Capacity & Filter

    Capacity, weight, filter PN, drain plug torque, change interval.

    Fluid Type Specs

    Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.

    Coolant Capacity & Type

    Total system capacity, OEM coolant spec, flush interval, bleed tips.

    Transmission Fluid & Service

    Trans model, fluid spec, capacity, filter PN, service interval.

    Torque Specifications

    Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.

    Brake Pad & Rotor Specs

    Pad PNs, rotor size, min thickness, caliper torque.

    Tire Size & Pressure

    OEM size, cold psi, bolt pattern, wheel size, TPMS.

    Battery Size & Group

    Group size, CCA, AGM/flooded, dimensions, reset note.

    A/C Refrigerant & Oil

    R-134a or R-1234yf, charge oz, PAG oil spec.

    Bulb Sizes (Headlight, Tail, Fog)

    Headlight, fog, tail, turn, reverse, interior.

    Factory Maintenance Schedule

    Service intervals by mileage, severe-duty notes, known issues.

    Towing Capacity & Payload

    Max tow, payload, GVWR/GCWR, hitch class by trim.

    Fuse Box Diagram & Amperage

    Fuse box locations, layout, amps, and what each fuse controls.

    Wheel Alignment Specifications

    Camber, caster, toe ranges (front & rear), adjustability notes.

    Paint Color Codes

    All factory colors with paint codes, sticker location, touch-up tips.

    Wiper Blade Sizes

    Driver/passenger/rear blade size, attachment, OEM + cross-refs.

    Spark Plug Type & Gap

    Plug PN, gap, torque, interval by engine.

    Transmission & Axle Gear Ratios

    Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.

    Key Fob Programming

    DIY programming steps, FCC ID, fob PN, battery, transponder.

    Same spec — other model years

    Maintenance & repair guides

    Browse by make

    Running an auto or diesel repair shop?

    Compare Repairius to the shop software you're paying for

    $99.99/month (first location included), unlimited users, 14-day free trial.

    Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-06-26.

    Driving or Managing a Fleet?

    Use Dispatchtool for truck navigation, driver communication, dispatching, and fleet management.

    Visit Dispatchtool
    Run your shop from estimate to payment

    Don't overhaul your shop. Test Repairius on your next job.

    Repairius keeps estimates, work orders, real-time job assignment, customer and vehicle history, inventory, and payments in one place — on desktop and in your pocket.

    14-day free trial · credit card required · cancel anytime

    Not a mechanic? Send Repairius to your shop — they can run estimates, jobs, and invoices in one place.

    Know someone who needs this?

    Share this page with a mechanic, a shop owner, or a friend working on the same problem.

    Know a mechanic or shop owner Repairius could help?

    Send them Repairius in one tap. Free listing, online booking, reminders and the full shop workflow.

    Text them Email