2017 Toyota Highlander — Torque Specifications
Quick-reference fastener torques for wheels, engine, transmission, and brakes
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2017 Toyota Highlander? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Quick reference
| Fastener | Torque (ft-lb / Nm) | Notes |
|---|---|---|
| Wheel lug nuts | 76 ft-lb (103 Nm) | Tighten in a star/cross pattern; recheck after 25–50 miles. |
| Engine oil drain plug | 27–30 ft-lb (37–41 Nm) | Replace crush washer; aluminum pan threads—do not overtighten. |
| Automatic trans drain plug (UA80E/UA80F 8AT) | 15–20 ft-lb (20–27 Nm) | WS fluid pan drain/overflow plugs are light-torque; new gasket recommended. |
| Automatic trans fill/inspection plug (UA80E/UA80F 8AT) | 29–36 ft-lb (39–49 Nm) | Always open fill first; verify correct temp/level set procedure. |
| Hybrid transaxle drain/fill (P314 eCVT) | 26–32 ft-lb (35–43 Nm) | Hybrid uses Toyota ATF WS; confirm plug locations and torque. |
| Front brake caliper bracket bolts | 79–91 ft-lb (107–123 Nm) | Clean threads; medium threadlocker if specified by OEM. |
| Rear brake caliper bracket bolts | 54–70 ft-lb (73–95 Nm) | Inspect slide boots and pad abutments. |
| Front caliper slide pins/guide pins | 24–28 ft-lb (32–38 Nm) | Lightly grease pin bodies only; keep threads dry unless OEM says otherwise. |
| Rear caliper slide pins/guide pins | 20–25 ft-lb (27–34 Nm) | Do not twist/tear boots when tightening. |
| Front axle shaft nut | 159–203 ft-lb (215–275 Nm) | Range covers FWD/AWD and supplier variations; replace/stake nut and/or install new cotter pin as equipped. |
| Spark plugs (gas engines) | 12 mm: 13–15 ft-lb (18–20 Nm); 14 mm: 18–22 ft-lb (24–30 Nm) | 2GR‑FKS/FXS V6 uses 12 mm iridium; 1AR‑FE 4‑cyl uses 14 mm. No anti-seize on plated plugs; torque to clean, dry threads. |
| Valve cover bolts | 62–80 in-lb (7–9 Nm) | Small fasteners—use inch‑pound wrench; tighten in several passes from center outward. |
| Intake manifold upper/plenum bolts | 89–106 in-lb (10–12 Nm) | Plastic surge tank fasteners; follow crisscross sequence and stage torque. |
| Intake manifold to cylinder head (lower) | 13–18 ft-lb (18–25 Nm) | Use new gaskets; torque in sequence from center outward. |
Wheel lug torque pattern
- 5-lug Highlander wheels should be torqued in a star/cross pattern: 1 → 3 → 5 → 2 → 4.
- Make two passes: a snugging pass, then final torque to 76 ft-lb (103 Nm). Recheck torque after 25–50 miles, especially after tire rotations or wheel service.
Brake torque notes
- Caliper bracket vs. slide pin: Bracket bolts carry clamp load and see vibration—clean the threads in the knuckle/hub and bring them to spec (front 79–91 ft-lb; rear 54–70 ft-lb). Slide pins are lighter torque (front 24–28 ft-lb; rear 20–25 ft-lb); over-torque can bind pins and cause uneven pad wear.
- Use only high-temp silicone brake grease on pin bodies and abutment contact points; keep grease off threads and rotor friction surfaces. If the OEM specifies medium threadlocker for bracket bolts, apply sparingly to clean, dry threads.
- Always support the caliper to avoid hose strain. If a bracket bolt or pin feels spongy before reaching spec, stop and inspect for stripped threads or compressed rust scale.
Why torque matters
Applying the correct torque keeps fasteners from loosening while preventing damage to threads, gaskets, and components:
- Wheels: Under‑torque risks wheel movement; over‑torque can stretch studs and warp rotors. The star pattern helps center the wheel and evenly load the rotor hat.
- Engine/trans drains and fills: These plugs often thread into aluminum cases or pans. Over‑torque can crack housings; under‑torque may cause leaks. Replace sealing washers and gaskets as required.
- Brakes: Proper torque prevents clunks, uneven pad wear, and rotor distortion. Bracket bolts handle structural loads; slide pins must float freely.
- Axle nuts: Correct preload protects wheel bearings. Many are single‑use; replace and stake or pin as designed.
- Spark plugs and valve cover/manifold hardware: Correct torque ensures sealing without stripping small fasteners or distorting plastic/composite components. Follow any specified tightening sequences and stage torques, especially on intake components.
Disclaimer: Torque values above are typical ranges for the 2017 Toyota Highlander family (2.7L 1AR‑FE, 3.5L 2GR‑FKS gas, and 2GR‑FXS hybrid with UA80E/UA80F 8‑speed or P314 eCVT). Critical fasteners should always be verified in the OEM service manual using your exact VIN, engine, and drivetrain.
Find a trusted shop on Repairius.
More specs for the 2017 Toyota Highlander
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2017 Toyota Highlander Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.