2019 Toyota Highlander Oil Capacity & Filter Guide
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2019 Toyota Highlander? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
The 2019 Toyota Highlander takes 6.4 quarts (6.1 L) of oil with a filter change for the V6 engine, and 4.6 quarts (4.4 L) for the 4-cylinder engine.
Quick answer
- Oil capacity (V6): 6.4 quarts / 6.1 L (with filter)
- Oil capacity (4-cyl): 4.6 quarts / 4.4 L (with filter)
- Recommended oil weight: SAE 0W-20
- Oil specification: API SN / ILSAC GF-5 or newer
- OEM oil filter part number: 04152-YZZA1 (for V6, cartridge style), 90915-YZZF2 (for 4-cyl, spin-on)
- Aftermarket filter cross-references (V6):
- Fram: CH9972
- Wix: 57064
- Mobil 1: M1C-154
Capacity by engine option
| Engine | Oil capacity (with filter) |
|---|---|
| 3.5L V6 (2GR-FKS) | 6.4 qts / 6.1 L |
| 2.7L 4-cylinder (1AR-FE) | 4.6 qts / 4.4 L |
Oil change interval
For the 2019 Highlander, Toyota recommends the following oil change intervals:
- Normal duty: Every 10,000 miles or 12 months, whichever comes first.
- Severe duty: Every 5,000 miles or 6 months. Severe duty conditions include frequent short trips, driving in dusty or dirty conditions, and extensive idling or low-speed driving.
Drain plug torque
- Drain plug torque (V6): 30 ft-lbs
- Drain plug torque (4-cyl): 30 ft-lbs
It is highly recommended to replace the crush washer with a new one at every oil change to prevent leaks. The Toyota part number for the crush washer is 90430-12031.
How to change the oil
- Warm up the engine for a few minutes to get the oil flowing.
- Safely raise and support the vehicle on a level surface.
- Place a drain pan under the oil pan and remove the drain plug.
- Allow the oil to drain completely, then reinstall the drain plug with a new crush washer.
- Remove the old oil filter. For V6 models, this will be a cartridge filter located in a housing on the oil pan.
- Install the new oil filter, making sure to lubricate the O-ring with fresh oil.
- Fill the engine with the correct amount and type of oil.
- Start the engine and check for leaks.
Common issues / tips
For the V6 engine, the oil filter is a cartridge type, which requires a special tool for removal (Toyota special tool 09228-06501, or a 64mm filter wrench). Be careful not to overtighten the filter housing, as it is made of plastic and can crack.
For the 4-cylinder engine, the oil filter is a traditional spin-on type. When installing the new filter, tighten it by hand until it is snug, then give it an additional 3/4 turn.
Need an oil change? Find a trusted shop on Repairius.
More specs for the 2019 Toyota Highlander
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2019 Toyota Highlander Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.