2019 Honda Odyssey Oil Capacity & Filter Specs

The 2019 Honda Odyssey takes 5.7 quarts of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 5.7 US Quarts (5.4 Liters)
• Recommended Oil Weight: 0W-20
• Oil Type Specification: API Premium Grade Drained and Refilled Only, or API Certification Seal
• OEM Oil Filter Part Number: 15400-PLM-A02
• Aftermarket Oil Filter Cross-References:
  • Fram: PH7317 (Extra Guard), FMSXA7317 (SynGuard)
  • Wix: 57356
  • Mobil 1: M1-110

Capacity by Engine Option

The 2019 Honda Odyssey is equipped with a single engine option:

Oil Change Interval

Honda recommends following the Maintenance Minder system for optimal oil change intervals. This system calculates the oil's remaining life based on driving conditions and starts at 100%. When it reaches 15%, a service reminder will appear.

• Normal Driving Conditions: Typically 7,500 to 10,000 miles or 12 months, whichever comes first.
• Severe Driving Conditions: If your driving primarily involves short trips, extreme temperatures, heavy towing, or extensive idling, the Maintenance Minder may indicate an oil change sooner, potentially around 3,000 to 5,000 miles.

Drain Plug Torque

The oil drain plug for the 2019 Honda Odyssey requires a torque of 29 lb-ft (39 N·m). Always replace the crush washer with a new one during every oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is typically 94109-14000, though it's always best to confirm with your dealer or parts supplier.

How to Change the Oil

1. Warm Up the Engine: Drive the vehicle for a few minutes to bring the oil to operating temperature, which helps it drain more easily.
2. Lift and Secure: Safely lift the front of the vehicle using a jack and secure it with jack stands. Always use appropriate safety precautions.
3. Locate Drain Plug: Place a suitable drain pan beneath the oil drain plug, located on the oil pan beneath the engine.
4. Drain Oil: Carefully remove the drain plug with a wrench (usually 17mm or 19mm) and allow all the old oil to drain completely. Inspect the old oil for any metallic flakes or abnormalities.
5. Replace Crush Washer: Once drained, clean the drain plug and install a new crush washer. Reinstall the drain plug and torque it to 29 lb-ft (39 N·m).
6. Remove Oil Filter: Place the drain pan under the oil filter, located on the front of the engine. Use an oil filter wrench to loosen and remove the old filter. Be prepared for additional oil to drain.
7. Install New Filter: Apply a thin coat of new engine oil to the rubber gasket of the new oil filter. Thread the new filter on by hand until the gasket makes contact with the engine block, then tighten it an additional 3/4 to 1 full turn. Do not overtighten.
8. Add New Oil: Lower the vehicle. Locate the oil fill cap on top of the engine and add approximately 5.5 quarts of the recommended 0W-20 oil. Wait a few minutes for the oil to settle.
9. Check Level: Check the oil level using the dipstick. It should be between the "MIN" and "MAX" marks. Add more oil gradually if needed, rechecking the dipstick each time. Ensure the level is not above "MAX."
10. Start Engine and Check for Leaks: Start the engine and let it run for a few minutes. Check for any leaks around the drain plug and oil filter. Turn off the engine and recheck the oil level after a few minutes.
11. Reset Maintenance Minder: Follow the instructions in your owner's manual to reset the Maintenance Minder system.

Common Issues / Tips for this Generation

• VCM (Variable Cylinder Management) Considerations: The 2019 Odyssey, like many Honda V6 engines, utilizes Variable Cylinder Management (VCM). Some owners experience increased oil consumption related to VCM or piston ring issues. While 0W-20 is the factory recommended oil, maintaining consistent oil changes and monitoring oil levels closely is crucial. Always ensure the correct oil weight and specification are used.
• Maintenance Minder Accuracy: Trust the Maintenance Minder system. It's designed to optimize service intervals based on actual driving conditions, which can save you money and ensure proper maintenance.
• Oil Filter Location: The oil filter on the J35Y6 engine is positioned on the front of the engine, making it relatively accessible for DIY oil changes.
• Always Replace Crush Washer: This is a small but critical step. Reusing the old crush washer can lead to annoying and potentially damaging oil leaks.

Need an oil change? Find a trusted shop on Repairius.