2020 Honda Odyssey Oil Capacity & Filter

The 2020 Honda Odyssey takes 5.7 quarts (5.4 liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 5.7 quarts (5.4 liters)
• Recommended Oil Weight: 0W-20
• Oil Type Spec: API Premium Grade અથવા Honda HTO-06 equivalent (consult your owner's manual for the most up-to-date specification)
• OEM Oil Filter Part Number: 15400-PLM-A02 (or consult your dealer for the latest part number)
• Aftermarket Oil Filter Cross-References:
  • Fram: PH7317
  • Wix: 51356
  • Mobil 1: M1-110

Capacity by Engine Option

The 2020 Honda Odyssey is exclusively offered with one engine option, the 3.5L V6 (J35Y6).

Oil Change Interval

Honda's Maintenance Minder system in your 2020 Odyssey will generally indicate when an oil change is due. This is typically:

• Normal Duty: 7,500 - 10,000 miles or 12 months, whichever comes first.
• Severe Duty (e.g., frequent short trips, extreme temperatures, towing): 3,000 - 5,000 miles or 6 months, whichever comes first.

Always refer to your vehicle's owner's manual and the Maintenance Minder system for the most accurate and personalized service recommendations.

Drain Plug Torque

The oil drain plug on the 2020 Honda Odyssey should be torqued to 29 lb-ft (39 N-m). It is highly recommended to replace the crush washer with a new one every time you perform an oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is typically 94109-14000, but confirm with your dealer.

How to Change the Oil

1. Warm Up: Drive the vehicle for a few minutes to bring the oil to operating temperature.
2. Lift & Secure: Safely lift the front of the vehicle using a jack and secure it with jack stands.
3. Locate: Place a drain pan under the oil pan. Locate the oil drain plug. It's a 17mm bolt.
4. Drain: Carefully remove the drain plug and allow the old oil to drain completely.
5. Replace Plug & Washer: Install a new crush washer on the drain plug and reinsert it, tightening to 29 lb-ft (39 N-m).
6. Remove Filter: Locate the oil filter (typically on the front of the engine near the exhaust manifold). Use an oil filter wrench to remove it.
7. New Filter Prep: Apply a thin film of new oil to the rubber gasket of the new oil filter.
8. Install Filter: Hand-tighten the new oil filter until the gasket makes contact, then turn an additional 3/4 to 1 full turn. Do not overtighten.
9. Add Oil: Lower the vehicle. Remove the oil cap and carefully pour in approximately 5.5 quarts of fresh 0W-20 oil.
10. Check Level: Start the engine and let it run for a minute. Shut it off, wait a few minutes, then check the oil level with the dipstick. Add more oil if necessary, ensuring the level is between the "min" and "max" marks.
11. Reset Maintenance Minder: Follow the instructions in your owner's manual to reset the oil life monitor.

Common Issues / Tips

For the 2020 Honda Odyssey (part of the fifth generation, 2018-present):

• VCM (Variable Cylinder Management): The J35Y6 engine utilizes Variable Cylinder Management, which can sometimes lead to increased oil consumption in some engines as they age. Regularly check your oil level between changes, especially if you notice any unusual consumption. Using the recommended 0W-20 oil is crucial for proper VCM operation.
• Oil Filter Location: The oil filter on this generation Odyssey is easily accessible from above or below, making changes relatively straightforward.
• Accessory Belt Tensioner: Some owners have reported issues with the accessory belt tensioner on these J-series engines. While not directly related to oil, it's a component to be aware of during routine maintenance.
• Crush Washer: Always use a new crush washer on the drain plug. Reusing the old one can lead to oil leaks.
• Genuine Honda Parts: While aftermarket filters are available, many Honda enthusiasts prefer genuine Honda oil filters (Part Number: 15400-PLM-A02) for their known quality and fit.

Need an oil change? Find a trusted shop on Repairius.