2024 International MV Oil Capacity & Filter Specs
An ASE master tech guide to heavy-duty oil capacities, fluid specs, and filter part numbers for the 2024 International MV.
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2024 International MV? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
The 2024 International MV takes between 15 quarts (14.2 L) and 23.7 quarts (22.4 L) of oil, depending on whether it is equipped with the Cummins B6.7 or the larger Cummins L9 engine and the specific oil pan option ordered. As a medium-duty workhorse used for everything from delivery box trucks to dump applications, maintaining the proper oil level and specification is critical to keeping this truck on the road and out of the shop.
Quick answer
Here is the quick reference guide for the standard 2024 International MV equipped with the popular Cummins B6.7 engine:
- Oil Capacity: 15 to 17.5 quarts (14.2 to 16.5 L) with filter, depending on the oil pan configuration.
- Recommended Weight: 15W-40 (for temperatures above 5°F) or 5W-40 Synthetic (for extreme cold climates).
- Oil Specification: API CK-4 / Cummins CES 20086.
- OEM Oil Filter Part Number: Fleetguard LF3970.
- Aftermarket Cross-References: WIX 57349, Baldwin BT7349, Donaldson P558615 (Consult dealer for exact cross-reference matching your specific build sheet).
Capacity by engine option
The 2024 International MV series is powered by Cummins diesel engines. Because these are custom-ordered commercial chassis, the exact oil pan capacity can vary slightly based on clearance requirements. Always check your dipstick after the initial fill.
| Engine Model | Standard Oil Capacity (with filter) | Recommended Oil Viscosity |
|---|---|---|
| Cummins B6.7 (6.7L) | 15.0 - 17.5 Quarts (14.2 - 16.5 L) | 15W-40 or 5W-40 |
| Cummins L9 (9.0L) | 21.0 - 23.7 Quarts (19.9 - 22.4 L) | 15W-40 or 5W-40 |
Oil change interval
Medium-duty diesel engines operate under different duty cycles than passenger vehicles. Service intervals are dictated by mileage, engine hours, or time—whichever comes first.
- Normal Duty (Highway / Light Delivery): Change the oil and filter every 15,000 miles, 500 engine hours, or 6 months.
- Severe Duty (Stop-and-Go, PTO use, Towing, Dusty Conditions): Change the oil and filter every 10,000 miles, 250 to 350 engine hours, or 6 months. High idle times significantly accelerate oil degradation.
Drain plug torque
- Drain Plug Torque: 37 ft-lbs (50 Nm) for both the Cummins B6.7 and L9 standard oil pans.
- Crush Washer Note: Always inspect and replace the copper or copper-composite crush washer on the drain plug. Reusing a deformed washer on a heavy-duty diesel engine is a common cause of persistent leaks under extreme vibration.
How to change the oil
Servicing a commercial truck like the International MV requires heavy-duty drain pans and appropriate safety gear.
- Warm the Engine: Run the engine until it reaches operating temperature to suspend contaminants in the oil, then shut it down.
- Drain the Oil: Position a high-capacity catch pan (at least 30-quart capacity) under the oil pan. Remove the drain plug and let the oil drain completely.
- Replace the Filter: Using a heavy-duty filter wrench, loosen the oil filter. Carefully lower it (it will be heavy and full of oil). Wipe the filter housing base clean.
- Install New Filter: Pre-fill the new oil filter with fresh oil to prevent a dry start. Lubricate the rubber gasket on the new filter with clean oil, thread it on until the gasket makes contact, and tighten 3/4 to 1 full turn by hand.
- Reinstall Drain Plug: Install the drain plug with a new sealing washer and torque to 37 ft-lbs.
- Fill and Verify: Fill the engine with the specified capacity of API CK-4 heavy-duty diesel oil. Start the engine, check for leaks, and monitor oil pressure. Shut it off, wait 15 minutes, and verify the final level on the dipstick.
Common issues / tips
When servicing the 2024 International MV, pay special attention to the Cummins emission systems and fuel filters. The B6.7 and L9 engines require simultaneous fuel filter changes (both the chassis-mounted water separator and engine-mounted filter) at every oil change interval to prevent high-pressure fuel pump failures. Furthermore, be cautious of overfilling the oil; excessive oil can cause foaming, leading to oil pressure drops and potential blow-by that can prematurely clog the Diesel Particulate Filter (DPF). Lastly, don't forget to grease the chassis, steering linkages, and driveline U-joints while you are under the truck draining the oil.
Need an oil change? Find a trusted shop on Repairius.
More specs for the 2024 International MV
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2024 International MV Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.