2025 Nissan Frontier Coolant Capacity & Type
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2025 Nissan Frontier? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
The 2025 Nissan Frontier holds approximately 10.0 quarts (9.5 liters) of coolant in its cooling system.
Quick Answer
- Total Cooling System Capacity: 10.0 quarts (9.5 liters)
- OEM Coolant Spec: Nissan Genuine Long Life Antifreeze/Coolant (Blue, Phosphated Organic Acid Technology - POAT, Nissan L250 Super Long Life/Nissan L255NP)
- Mix Ratio: 50/50 Pre-mix or 50/50 Concentrate with distilled water
Capacity by Engine Option
The 2025 Nissan Frontier is expected to feature the 3.8L V6 engine across all trims, with a consistent coolant capacity.
| Engine | Capacity (Quarts) | Capacity (Liters) |
|---|---|---|
| 3.8L V6 (VQ38DD) | 10.0 | 9.5 |
Flush Interval
Nissan recommends specific coolant flush intervals to maintain optimal cooling system performance for your 2025 Frontier:
- Normal Duty: Replace initially at 105,000 miles or 84 months, then every 75,000 miles or 60 months thereafter.
- Severe Duty: If your vehicle is subjected to severe conditions (e.g., heavy towing, extreme temperatures, off-roading, frequent short trips), it's advisable to inspect your coolant more frequently and consider reducing the replacement interval. Typically, severe duty service might warrant replacement at 60,000 miles or 48 months.
Always consult your owner's manual for the most accurate and up-to-date maintenance schedule.
How to Refill & Bleed
Properly refilling and bleeding the cooling system in your 2025 Nissan Frontier is crucial to prevent air pockets, which can lead to overheating. Here's a general procedure:
- Safety First: Ensure the engine is completely cool before attempting any work on the cooling system. Wear appropriate personal protective equipment (PPE) like gloves and eye protection.
- Drain Coolant: If performing a flush, open the radiator drain cock (petcock) located at the bottom of the radiator and remove the radiator cap to allow the old coolant to drain completely. Some models may also have engine block drain plugs.
- Flush System (Optional): If flushing, close the drain cock, refill with distilled water, run the engine with the heater on until it reaches operating temperature, then drain again. Repeat until the drained water is clear. Consider using a cooling system cleaner designed for your coolant type.
- Refill: Close the radiator drain cock. Slowly add new Nissan Genuine Long Life Antifreeze/Coolant (Blue) to the radiator filler neck until it reaches the top. Fill the coolant reservoir to the "MAX" line.
- Bleeding Air:
- Start the engine with the radiator cap off (or loosely placed on top if splashing is an issue) and the heater set to full hot and fan on low. This helps open the heater core valve and circulate coolant through the entire system.
- Allow the engine to idle and reach operating temperature. As the engine warms up, the thermostat will open, and coolant will begin to circulate. You may see the coolant level drop in the radiator as air escapes. Top it off as needed.
- Gently squeeze the upper and lower radiator hoses several times to help dislodge trapped air bubbles.
- Nissan Frontier models often benefit from utilizing specific bleed screws if present on the thermostat housing or other high points in the system. While the 2025 model
More specs for the 2025 Nissan Frontier
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2025 Nissan Frontier Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.