2025 Nissan Frontier Oil Capacity & Filter Specs

The 2025 Nissan Frontier with its 3.8L V6 engine takes 6.0 quarts (5.7 liters) of 0W-20 synthetic motor oil.

Quick Answer

• Oil Capacity: 6.0 quarts (5.7 liters)
• Recommended Oil Weight: 0W-20 Full Synthetic
• Oil Type Specification: API SP or ILSAC GF-6B
• OEM Oil Filter Part Number: Consult Dealership
• Aftermarket Oil Filter Cross-References:
  • Fram: PH10075
  • Wix: 57060
  • Mobil 1: M1-110

Capacity by Engine Option

Oil Change Interval

Adhering to the factory-recommended oil change intervals is crucial for the longevity of your 2025 Nissan Frontier.

• Normal Duty Driving: Every 7,500 miles or 6 months, whichever comes first.
• Severe Duty Driving: Every 5,000 miles or 6 months, whichever comes first. Severe duty conditions include frequent short trips, extensive idling, towing, driving in dusty conditions, or extreme temperatures.

Drain Plug Torque

The oil drain plug on your 2025 Nissan Frontier should be torqued to 25 ft-lbs (34 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number should be confirmed with your Nissan dealer.

How to Change the Oil

Changing the oil on your 2025 Nissan Frontier is a straightforward maintenance task for the DIY enthusiast. Always consult your owner's manual for the most accurate and detailed instructions.

1. Gather Supplies: Ensure you have the correct oil, oil filter, drain pan, wrench for the drain plug, oil filter wrench, and a new crush washer.
2. Warm the Engine: Run the engine for a few minutes to bring the oil to operating temperature, allowing it to drain more easily.
3. Lift and Secure: Safely lift the front of the vehicle using a jack and secure it with jack stands on a level surface.
4. Drain Oil: Place the drain pan beneath the oil pan, remove the drain plug, and allow all the old oil to completely drain.
5. Replace Filter: Locate and remove the old oil filter. Apply a thin coat of new oil to the gasket of the new filter before installing it. Hand-tighten until snug, then turn an additional 3/4 to 1 full turn (or as per filter instructions).
6. Reinstall Drain Plug: Install the new crush washer on the drain plug and reinstall it, tightening to 25 ft-lbs (34 Nm).
7. Add New Oil: Lower the vehicle and fill the engine with the recommended 6.0 quarts of 0W-20 full synthetic motor oil.
8. Check Level & Leaks: Start the engine and let it run for a few minutes. Check for any leaks around the drain plug and oil filter. Turn off the engine, wait a few minutes, then check the oil level on the dipstick and top off if necessary.

Common Issues / Tips for this Generation

• Direct Injection Considerations: The 3.8L V6 engine utilizes direct injection, which can sometimes lead to carbon buildup on intake valves over time. While oil choice doesn't directly prevent this, using a high-quality full synthetic oil like the recommended 0W-20 meeting API SP or ILSAC GF-6B can help maintain engine cleanliness and performance.
• Proper Oil Specification is Key: The 2025 Frontier specifies 0W-20 and the latest API SP or ILSAC GF-6B standards. Using oils that do not meet these specifications can lead to increased engine wear and potentially void your warranty. These specifications ensure the oil provides optimal protection against low-speed pre-ignition (LSPI) and timing chain wear.
• Regular Oil Changes: Given the potential for varied driving conditions, adhering strictly to the recommended oil change intervals, especially the severe duty schedule if applicable, will maximize engine life and maintain warranty compliance.
• Monitor Oil Level: It's always a good practice to periodically check your oil level between changes, especially before long trips, to ensure it remains within the proper range.

Need an oil change? Find a trusted shop on Repairius.