2016 Nissan Rogue Oil Capacity & Filter

The 2016 Nissan Rogue with the 2.5L QR25DE engine takes 4.9 quarts (4.6 liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 4.9 quarts (4.6 liters)
• Recommended Oil Weight: 0W-20
• Oil Specification: API SN or later, ILSAC GF-5 or later
• OEM Oil Filter Part Number: 15208-9E01A
• Aftermarket Oil Filter Cross-References:
  • Fram: PH6607
  • Wix: 51356
  • Mobil 1: M1-110

Capacity by Engine Option

Oil Change Interval

Nissan recommends the following oil change intervals for the 2016 Rogue:

• Normal Duty: Every 5,000 miles or 6 months, whichever comes first.
• Severe Duty: Every 3,750 miles or 3 months, whichever comes first. Severe duty conditions include frequent short trips, driving in dusty conditions, extensive idling, or towing.

Drain Plug Torque

The oil drain plug on the 2016 Nissan Rogue (2.5L engine) should be torqued to 25 ft-lbs (34 Nm). Always replace the crush washer with a new one to ensure a proper seal and prevent leaks. The crush washer is typically 12mm.

How to Change the Oil

1. Safely lift and support the front of the vehicle. Ensure it is stable on jack stands or a lift.
2. Locate the oil drain plug on the oil pan, typically on the passenger side of the vehicle.
3. Place a drain pan large enough to hold 5 quarts of oil directly under the drain plug.
4. Using a 14mm wrench or socket, carefully loosen and remove the drain plug. Allow all the old oil to drain completely.
5. Once the oil has drained, replace the old crush washer with a new one on the drain plug and reinsert the drain plug. Tighten to 25 ft-lbs (34 Nm).
6. Locate the oil filter, which is typically on the front side of the engine, easily accessible from underneath or from the top after removing engine covers.
7. Place the drain pan under the oil filter, as some oil will spill when removed.
8. Using an oil filter wrench, loosen and remove the old oil filter. Be prepared for oil to escape.
9. Apply a thin film of new engine oil to the rubber gasket of the new oil filter.
10. Hand-tighten the new oil filter until snug, then turn an additional 3/4 to 1 full turn (or as per filter manufacturer's instructions).
11. Lower the vehicle.
12. Remove the oil filler cap on top of the engine.
13. Carefully pour 4.9 quarts of the recommended 0W-20 engine oil into the filler neck.
14. Replace the oil filler cap.
15. Start the engine and let it run for a few minutes to circulate the new oil. Check for any leaks around the drain plug and oil filter.
16. Turn off the engine and wait a few minutes for the oil to settle.
17. Check the oil level using the dipstick. Add more oil if necessary to bring it to the "full" mark.

Common Issues / Tips

• CVT Transmission Fluid: The 2016 Nissan Rogue is equipped with a Continuously Variable Transmission (CVT). It's crucial to use the correct Nissan NS-3 CVT fluid if you ever service the transmission, as using the wrong fluid can cause significant damage. Do not confuse engine oil and transmission fluid.
• 2.5L (QR25DE) Reliability: The QR25DE engine is generally reliable, but consistent oil changes with the correct viscosity and specification are vital for its longevity. Neglecting oil changes can lead to timing chain wear and excessive oil consumption over time.
• Oil Filter Location: The oil filter is fairly accessible on the 2.5L engine, making DIY oil changes relatively straightforward.
• Crush Washer: Always use a new crush washer on the drain plug. Reusing old crush washers often leads to slow, persistent oil leaks.

Need an oil change? Find a trusted shop on Repairius.