2016 Ram ProMaster: Key Fastener Torque Specifications
Your guide to proper fastener tightening on the 2016 ProMaster van.
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2016 Ram ProMaster? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
""
Quick Reference Torque Specifications
This table provides the most commonly needed fastener torque specs for the 2016 Ram ProMaster series (1500, 2500, 3500). Values are provided in foot-pounds (ft-lb) and Newton-meters (Nm). Always consult an OEM service manual for the most accurate and detailed information.
| Fastener | Torque (ft-lb / Nm) | Notes |
|---|---|---|
| Wheel Lug Nuts | 133 ft-lb / 180 Nm | For 16-inch wheels. Tighten in a star pattern. |
| Oil Drain Plug (3.6L V6) | 20 ft-lb / 27 Nm | Always use a new gasket. |
| Transmission Drain Plug | 12-15 ft-lb / 16-20 Nm | Do not overtighten. |
| Front Brake Caliper Bracket Bolts | 148 ft-lb / 200 Nm | Often recommended to be replaced with new bolts. |
| Front Brake Caliper Slide Pins | 26 ft-lb / 35 Nm | Lubricate pins, but keep grease off braking surfaces. |
| Axle Nut (Hub Nut) | 200-220 ft-lb / 271-298 Nm | Critical fastener. Often torque-to-yield; verify procedure. |
| Spark Plugs (3.6L V6) | 13 ft-lb / 18 Nm | Apply to a cold engine. Do not use anti-seize on OEM plugs. |
| Valve Cover Bolts | 89 in-lb / 10 Nm | Tighten in the specified sequence to avoid warping. |
| Intake Manifold Bolts (Upper) | 89 in-lb / 10 Nm | Tighten in two stages per the service manual sequence. |
Wheel Lug Torque Pattern
Properly torquing wheel lug nuts is critical for safety and to prevent warping brake rotors. For the Ram ProMaster's 5-lug pattern, always tighten the nuts in a star or cross sequence. Start by snugging all nuts by hand, then use your torque wrench to tighten them in the star pattern to the final specification. Never use an impact wrench to perform final torque.
- Tighten the first nut.
- Skip one nut and tighten the third nut.
- Skip another and tighten the fifth nut.
- Continue the pattern until all five nuts are torqued to 133 ft-lb / 180 Nm.
Brake Torque Notes
Brake system fasteners are safety-critical. When replacing brake components on your ProMaster, pay close attention to the caliper bracket bolts. These are high-torque fasteners and many manufacturers recommend replacing them with new, pre-coated bolts each time they are removed. Ensure threads in the steering knuckle are clean and dry before installation.
Caliper slide pins require a much lower torque value. Overtightening them can bind the caliper, leading to uneven pad wear and poor braking performance. Always clean and lubricate the slide pins with a high-temperature silicone-based brake grease.
Why Torque Matters
Torque is the measure of rotational force applied to a fastener. Using a calibrated torque wrench to tighten bolts to the manufacturer's specification is essential for three main reasons:
- Safety: Ensures fasteners, like those holding on your wheels or brakes, will not loosen from vibration and fall off.
- Reliability: Prevents fasteners and components from being damaged. Overtightening can stretch or break a bolt, or warp sensitive parts like valve covers and oil pans, leading to leaks and costly repairs.
- Performance: Ensures components operate as designed. A perfectly torqued cylinder head allows the head gasket to seal properly, while correctly torqued spark plugs ensure they transfer heat effectively.
Disclaimer: The torque values provided in this article are for quick reference only. Variations can exist based on specific sub-models and installed equipment. Always verify critical fastener specifications with an OEM service manual for your specific vehicle before beginning any work.
Find a trusted shop on Repairius. ""
More specs for the 2016 Ram ProMaster
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2016 Ram ProMaster Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.