2019 Subaru Crosstrek Oil Capacity & Filter

The 2019 Subaru Crosstrek takes 5.1 quarts (4.8 liters) of 0W-20 engine oil for both available engine options.

Quick Answer

• Oil Capacity: 5.1 quarts (4.8 liters)
• Recommended Oil Weight: 0W-20
• Oil Specification: API SN PLUS or later, or ILSAC GF-5 or later. Subaru also recommends using Genuine Subaru oil.
• OEM Oil Filter Part Number: 15208AA160
• Aftermarket Oil Filter Cross-References:
  • Fram: PH6607
  • Wix: 57055
  • Mobil 1: M1-108A

Capacity by Engine Option

Oil Change Interval

Subaru recommends the following oil change intervals for the 2019 Crosstrek:

• Normal Driving Conditions: Every 6,000 miles or 6 months, whichever comes first.
• Severe Driving Conditions: Every 3,000 miles or 3 months, whichever comes first.

Severe driving conditions include:

• Repeated short-distance driving
• Driving in dusty conditions
• Driving in extremely cold weather
• Extensive idling or low-speed driving
• Towing a trailer

Drain Plug Torque

The drain plug torque for the 2019 Subaru Crosstrek is 31.1 ft-lbs (42 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is 803916010.

How to Change the Oil

1. Warm up the engine: Drive the vehicle for a few minutes to bring the engine oil to operating temperature, which helps the oil drain more easily.
2. Lift and secure: Safely lift the front of the vehicle using a jack and secure it with jack stands. Always use appropriate safety precautions.
3. Locate drain plug: Place a suitable drain pan beneath the oil drain plug, which is typically found at the bottom of the oil pan.
4. Drain oil: Carefully remove the drain plug with a wrench and allow all the old oil to drain completely. Be mindful of hot oil.
5. Replace crush washer and plug: Once drained, replace the old crush washer with a new one and reinstall the drain plug. Torque to 31.1 ft-lbs (42 Nm).
6. Remove oil filter: Locate the oil filter, typically on the top of the engine compartment. Use an oil filter wrench to remove the old filter.
7. Prepare new filter: Apply a thin coat of new oil to the rubber gasket of the new oil filter.
8. Install new filter: Hand-tighten the new oil filter until snug, then turn an additional 1/2 to 3/4 turn. Do not overtighten.
9. Add new oil: Using a funnel, add 5.1 quarts of fresh 0W-20 engine oil to the engine through the oil filler cap.
10. Check oil level: Start the engine and let it run for a few minutes. Turn it off, wait a few minutes for the oil to settle, then check the oil level with the dipstick. Add more oil if necessary.
11. Check for leaks: Visually inspect the drain plug and oil filter for any signs of leaks.
12. Dispose of old oil: Properly dispose of the used oil and filter at a recycling center.

Common Issues / Tips

• Oil Consumption (2.0L FB20D): Some 2019 Crosstreks with the 2.0L FB20D engine may exhibit higher than normal oil consumption. It's crucial to regularly check your oil level between changes, especially if you notice any unusual oil usage. Consult your dealer if you suspect excessive oil consumption.
• CVT Fluid Change: While not directly related to engine oil, many owners often confuse or neglect CVT fluid changes. The 2019 Crosstrek with the Lineartronic CVT also has specific service intervals for its transmission fluid, which are separate from engine oil. Consult your owner's manual for CVT service recommendations.
• Top-Mounted Oil Filter: The top-mounted oil filter on the FB20 engine makes oil changes relatively easy and less messy compared to vehicles with bottom-mounted filters. This design allows for easier access and reduces the chance of oil dripping during removal.
• Subaru Genuine Oil: While other oils meeting the specifications are acceptable, Subaru often recommends using their "Subaru Genuine Oil" which is specially formulated for their Boxer engines.

Need an oil change? Find a trusted shop on Repairius.