2022 Subaru Crosstrek Oil Capacity & Filter

The 2022 Subaru Crosstrek takes 4.2 quarts (4.0 liters) of oil for both available engine options.

Quick Answer

• Oil Capacity: 4.2 US Quarts (4.0 Liters)
• Recommended Oil Weight: 0W-20
• Oil Type Specification: API SN PLUS or later, ILSAC GF-5 or later, or ACEA A1/B1, A3/B3, A3/B4, A5/B5
• OEM Oil Filter Part Number: 15208AA170 (Subaru)
• Aftermarket Oil Filter Cross-References:
  • Fram: PH6607
  • Wix: 57055
  • Mobil 1: M1-108A

Capacity by Engine Option

Oil Change Interval

Subaru recommends the following oil change intervals for the 2022 Crosstrek:

• Normal Driving Conditions: Every 6,000 miles or 6 months, whichever comes first.
• Severe Driving Conditions: Every 3,000 miles or 3 months, whichever comes first. Severe driving conditions include frequent short trips, sustained idling, driving in dusty conditions, or frequent towing.

Drain Plug Torque

The oil drain plug for the 2022 Subaru Crosstrek should be torqued to 30 ft-lbs (40 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is typically 803916010.

How to Change the Oil

1. Warm up the engine to operating temperature, then turn it off.
2. Safely lift the front of the vehicle and support it with jack stands.
3. Place a drain pan under the oil drain plug, located on the bottom of the oil pan.
4. Remove the drain plug with a wrench and allow the oil to drain completely.
5. Once drained, replace the drain plug with a new crush washer and torque to 30 ft-lbs.
6. Locate the oil filter, typically on the top front of the engine (for the 2.0L and 2.5L BOXER engines, it's easily accessible). Place a rag or small pan underneath to catch any drips.
7. Remove the old oil filter using an oil filter wrench.
8. Apply a thin coat of new oil to the rubber gasket of the new filter.
9. Install the new oil filter, tightening it by hand until snug, then an additional 1/2 to 3/4 turn. Do not overtighten.
10. Lower the vehicle.
11. Remove the oil cap and carefully pour in 4.0 quarts of the recommended 0W-20 oil.
12. Start the engine and let it run for a few minutes to circulate the oil. Check for any leaks around the drain plug and oil filter.
13. Turn off the engine and wait a few minutes for the oil to settle.
14. Check the oil level on the dipstick and add more oil if necessary, ensuring it's between the "low" and "full" marks.
15. Reset the oil maintenance reminder on your dashboard.

Common Issues / Tips

• Check Oil Regularly: Subaru Boxer engines are known to consume a small amount of oil between changes. It's crucial to check your oil level regularly (e.g., every 1,000 miles) and top off as needed, especially if you drive often or in severe conditions.
• Use the Right Oil: Adhering to the recommended 0W-20 weight and specifications (API SN PLUS or later, ILSAC GF-5 or later) is vital for the longevity and performance of your engine, particularly with Subaru's Boxer engine design.
• Accessible Oil Filter: The top-mounted oil filter on the 2022 Crosstrek's FB20D and FB25D engines makes oil changes significantly easier compared to older Subaru models where the filter was often tucked underneath.
• Crush Washer: Always replace the drain plug crush washer. Failing to do so can lead to oil leaks.
• Resetting the Maintenance Reminder: After an oil change, remember to reset the maintenance reminder in the infotainment system or instrument cluster. Consult your owner's manual for specific instructions for your trim level.

Need an oil change? Find a trusted shop on Repairius.