2015 Toyota Corolla Oil Capacity & Filter Specs

The 2015 Toyota Corolla takes 4.4 quarts (4.2 liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 4.4 US Quarts (4.2 Liters) with filter
• Recommended Oil Weight: SAE 0W-20
• Oil Type Spec: API SN (or later) or ILSAC GF-5 (or later) full synthetic
• OEM Oil Filter: Toyota Genuine Part Number 90915-YZZF2
• Aftermarket Oil Filter Cross-References:
  • Fram: PH4967
  • Wix: 57064
  • Mobil 1: M1-103

Capacity by Engine Option

For the 2015 model year, the Toyota Corolla was offered with two engine variations, both of which utilize the same oil capacity.

Oil Change Interval

Toyota recommends varying oil change intervals based on driving conditions:

• Normal Duty: Every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: Every 5,000 miles or 6 months, whichever comes first. Severe duty conditions include frequent short trips, extensive idling, towing, driving in dusty conditions, or extreme temperatures.

Always refer to your vehicle's owner's manual for the most accurate and up-to-date maintenance schedule.

Drain Plug Torque

The oil drain plug for the 2015 Toyota Corolla should be torqued to 30 ft-lbs (41 Nm). It is highly recommended to replace the crush washer (gasket) with a new one every time you perform an oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is 90430-12031.

How to Change the Oil

1. Gather your tools: new oil, new oil filter, drain pan, wrench for drain plug, oil filter wrench, torque wrench, new crush washer, and jack/jack stands.
2. Warm up the engine slightly for better oil flow, then turn it off.
3. Safely lift the front of the vehicle and secure it on jack stands.
4. Locate the oil drain plug on the oil pan, place the drain pan underneath, and remove the plug. Allow all the old oil to drain completely.
5. Replace the crush washer on the drain plug and reinsert the drain plug, tightening it to 30 ft-lbs.
6. Locate the oil filter, place the drain pan beneath it, and remove the old filter. Be prepared for a small amount of oil to spill.
7. Apply a thin film of new oil to the rubber gasket of the new oil filter.
8. Screw on the new oil filter by hand until snug, then tighten an additional 3/4 to 1 full turn, or as specified on the filter itself.
9. Lower the vehicle.
10. Remove the oil cap and carefully pour in the new oil, starting with about 4 quarts. Check the dipstick, then add the remaining amount gradually until the oil level is between the "low" and "full" marks.
11. Start the engine and let it run for a few minutes to circulate the new oil. Check for any leaks around the drain plug and oil filter.
12. Turn off the engine, wait a few minutes, and re-check the oil level, topping off if necessary.
13. Dispose of used oil responsibly.

Common Issues / Tips

• Plastic Undershield: The 2015 Corolla has a plastic undershield that needs to be removed (usually with several 10mm bolts and plastic clips) to access the oil filter and drain plug. Be careful with the plastic clips as they can be brittle.
• Cartridge vs. Spin-on Filter: The 2015 Corolla uses a spin-on style oil filter, which is generally straightforward to change.
• VVT-i System: The 1.8L engine in the Corolla utilizes Toyota's VVT-i (Variable Valve Timing with intelligence) system. Using the correct viscosity and type of oil is crucial for the proper functioning and longevity of this system.
• Oil Consumption: While not a widespread issue for all 2015 Corollas, some owners of this generation Toyota engines have reported higher than normal oil consumption as the vehicle ages. Regularly check your oil level between changes and top off as needed, especially if your vehicle has higher mileage.

Need an oil change? Find a trusted shop on Repairius.