2017 Toyota Corolla Oil Capacity & Filter

The 2017 Toyota Corolla takes 4.4 quarts (4.2 liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 4.4 US Quarts (4.2 Liters)
• Recommended Oil Weight: 0W-20
• Oil Type Specification: API SN PLUS or later, ILSAC GF-5 or later
• OEM Oil Filter Part Number: Toyota 90915-YZZF2
• Aftermarket Oil Filter Cross-References:
  • Fram: PH4967 or XG4967 (Ultra Synthetic)
  • Mobil 1: M1-103A
  • Wix: 51394

Capacity by Engine Option

For the 2017 model year, all Toyota Corollas sold in North America came with the same 1.8L 2ZR-FE engine (or 2ZR-FAE for Eco models). Therefore, the oil capacity remains consistent across all trims.

Oil Change Interval

Toyota recommends the following oil change intervals for the 2017 Corolla:

• Normal Duty: Every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: Every 5,000 miles or 6 months, whichever comes first. Severe duty conditions include frequent short trips (under 5 miles), extensive idling, towing, driving in dusty conditions, or extreme temperatures. It's advisable for most drivers to follow the severe duty schedule for optimal engine longevity.

Drain Plug Torque

The oil drain plug for the 2017 Toyota Corolla should be torqued to 27 ft-lbs (37 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is Toyota 90430-12031.

How to Change the Oil

Changing the oil on your 2017 Toyota Corolla is a straightforward process:

1. Safely lift and support the front of the vehicle using jack stands.
2. Locate the oil drain plug on the oil pan, usually on the passenger side, and place a drain pan underneath.
3. Remove the drain plug with a 14mm wrench and allow the old oil to drain completely.
4. Replace the crush washer on the drain plug and reinstall it, torquing to 27 ft-lbs.
5. Locate the spin-on oil filter towards the front of the engine, typically on the passenger side. Use an oil filter wrench to remove the old filter.
6. Apply a thin layer of new oil to the rubber gasket of the new filter and screw it on by hand until snug. Then, tighten an additional 3/4 to 1 full turn.
7. Lower the vehicle and fill the engine with 4.4 quarts of new 0W-20 engine oil through the oil fill cap.
8. Start the engine and let it run for a few minutes. Check for any leaks.
9. Turn off the engine, wait a few minutes for the oil to settle, and then check the oil level on the dipstick, adding more if necessary.

Common Issues / Tips

• Oil Consumption: Some 1.8L Toyota engines, including those found in the 2017 Corolla, can exhibit higher-than-average oil consumption as they age. It's wise to regularly check your oil level with the dipstick, especially between oil changes, and top off as needed.
• Plastic Undercarriage Shield: The 2017 Corolla has a plastic undercarriage splash shield that needs to be removed or partially lowered to access the oil filter and drain plug. This typically involves removing several 10mm bolts and plastic clips.
• Genuine Toyota Filters: While quality aftermarket filters are acceptable, many enthusiasts prefer genuine Toyota oil filters (part number 90915-YZZF2) for their consistent quality and robust construction. These are often readily available at Toyota dealerships or online.
• Torque Wrench: Using a torque wrench for both the drain plug and oil filter (if specified by the filter manufacturer) can prevent overtightening, which can lead to stripped threads or cracked components.

Need an oil change? Find a trusted shop on Repairius.