2021 Jeep Cherokee Oil Capacity & Filter

The 2021 Jeep Cherokee takes between 5.0 to 5.5 quarts of 0W-20 or 5W-20 engine oil, depending on the engine. This guide provides comprehensive information on oil capacity, recommended oil types, filter part numbers, and maintenance tips for your 2021 Jeep Cherokee.

Quick Answer

• Oil Capacity:
  • 2.4L Tigershark MultiAir I-4: 5.5 quarts (5.2 liters)
  • 3.2L Pentastar V6: 5.5 quarts (5.2 liters)
  • 2.0L Hurricane I-4 (Turbo): 5.0 quarts (4.7 liters)
• Recommended Oil Weight: 0W-20 or 5W-20 (refer to your owner's manual for specific engine requirements)
• Oil Type Spec: API SP or equivalent, meeting FCA Material Standard MS-6395
• Oil Filter Part Numbers:
  • 2.4L Tigershark MultiAir I-4:
    • OEM Mopar: 68102241AA
    • Fram Extra Guard: CH11665
    • Wix XP: WL10010XP
    • Mobil 1: M1C-251
  • 3.2L Pentastar V6:
    • OEM Mopar: 68191349AB
    • Fram Extra Guard: CH11665
    • Wix XP: WL10010XP
    • Mobil 1: M1C-251
  • 2.0L Hurricane I-4 (Turbo):
    • OEM Mopar: 68507851AA
    • Fram Extra Guard: CH12891
    • Wix XP: WL10557
    • Mobil 1: M1C-451A

Capacity by Engine Option

Oil Change Interval

For most driving conditions, the recommended oil change interval for the 2021 Jeep Cherokee is 10,000 miles or 12 months, whichever comes first. However, if you regularly operate your vehicle under severe duty conditions, such as:

• Frequent short trips (less than 5 miles)
• Extreme hot or cold temperatures
• Towing or heavy hauling
• Operating in dusty or sandy environments
• Extensive idling or stop-and-go driving

It is highly recommended to change your oil every 5,000 miles or 6 months.

Drain Plug Torque

The oil drain plug torque specification for the 2021 Jeep Cherokee is 20 ft-lbs (27 Nm) for all engine options. Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. Copper or aluminum crush washers are commonly used.

How to Change the Oil

Changing the oil on your 2021 Jeep Cherokee is a straightforward process:

1. Gather your supplies: Correct oil, new oil filter, drain pan, wrench for the drain plug, oil filter wrench, funnel, new crush washer, and rags.
2. Warm up the engine: Drive the vehicle for a few minutes to bring the oil to operating temperature, allowing it to drain more easily.
3. Lift and secure: Safely lift the front of the vehicle using a jack and secure it with jack stands.
4. Locate drain plug and filter: Identify the oil pan drain plug and the oil filter.
5. Drain the oil: Place the drain pan under the plug. Carefully remove the drain plug and allow all the old oil to drain completely.
6. Replace drain plug: Once drained, reinstall the drain plug with a new crush washer and torque to 20 ft-lbs (27 Nm).
7. Remove old filter: Position the drain pan under the oil filter. Use an oil filter wrench to loosen and remove the old filter. Be prepared for some residual oil to spill.
8. Prepare new filter: Apply a thin coat of new oil to the rubber gasket of the new oil filter.
9. Install new filter: Hand-tighten the new oil filter until snug, then turn an additional 3/4 to 1 full turn. Consult the filter's instructions for specific torque recommendations if available.
10. Add new oil: Using a funnel, add the recommended amount of new oil through the oil fill cap.
11. Check level: Start the engine and let it run for a minute to circulate the oil. Turn off the engine, wait a few minutes, and then check the oil level with the dipstick. Add more oil if necessary to reach the "full" mark.
12. Dispose of old oil: Properly dispose of the old oil and filter at a certified recycling center.

Common Issues / Tips

• 2.4L Tigershark Engine Oil Consumption: It's not uncommon for some 2.4L Tigershark engines to consume a small amount of oil between changes. Regularly check your oil level and top off as needed.
• Location of Oil Filter: For the 2.4L Tigershark and 3.2L Pentastar engines, the oil filter is a cartridge type located at the top of the engine, making it relatively easy to access. The 2.0L Hurricane has a more traditional spin-on filter.
• Use the Right Oil: Always use engine oil that meets the FCA Material Standard MS-6395 specification to ensure proper lubrication and longevity of your engine.
• Reset Oil Life Monitor: After an oil change, remember to reset your vehicle's oil life monitoring system. Consult your owner's manual for the exact procedure.
• Underbody Cover: The 2021 Jeep Cherokee may have an underbody splash shield that needs to be removed to access the drain plug and oil filter. These are typically held in place by a few bolts or clips.

Need an oil change? Find a trusted shop on Repairius.