2020 Jeep Cherokee Oil Capacity & Filter Guide

The 2020 Jeep Cherokee takes between 5.0 and 5.5 quarts (4.7 to 5.2 liters) of 0W-20 or 5W-20 engine oil, depending on the engine.

Quick Answer

Here's a quick overview of the essential oil change information for your 2020 Jeep Cherokee:

• Oil Capacity:
  • 2.0L Turbo (ESS): 5.5 Quarts (5.2 Liters)
  • 2.4L Tigershark MultiAir (ESS): 5.0 Quarts (4.7 Liters)
  • 3.2L Pentastar V6 (ESS): 5.5 Quarts (5.2 Liters)
• Recommended Oil Weight: 0W-20 or 5W-20 (refer to your owner's manual for the specific engine recommendations)
• Oil Specification: API SP or equivalent, meeting Chrysler MS-6395 (0W-20) or MS-6395 (5W-20)
• Oil Filter Part Numbers:
  • 2.0L Turbo:
    • OEM: Consult dealer for specific part number
    • Fram: CH12918
    • Wix: WL10090
    • Mobil 1: M1C-258A
  • 2.4L Tigershark MultiAir:
    • OEM: Consult dealer for specific part number
    • Fram: CH11665
    • Wix: 57060
    • Mobil 1: M1C-153
  • 3.2L Pentastar V6:
    • OEM: Consult dealer for specific part number
    • Fram: CH11665
    • Wix: 57060
    • Mobil 1: M1C-153

Capacity by Engine Option

ESS = Engine Stop/Start system, which may impact oil requirements. Always verify with your owner's manual.

Oil Change Interval

Maintaining the correct oil change interval is crucial for your 2020 Jeep Cherokee's longevity and performance. Jeep recommends the following:

• Normal Duty: Typically every 10,000 miles (16,000 km) or 12 months, whichever comes first. The onboard Oil Change Indicator System will also alert you when an oil change is due.
• Severe Duty: If you operate your vehicle under severe conditions, such as frequent short trips, extensive idling, towing, or dusty environments, it is recommended to change your oil every 4,000-5,000 miles (6,500-8,000 km) or 6 months, whichever comes first. Always check your owner's manual for the most accurate severe duty recommendations.

Drain Plug Torque

Properly torquing the drain plug is essential to prevent leaks and damage to the oil pan.

• Drain Plug Torque: 20 ft-lbs (27 Nm)
• Crush Washer: Always use a new crush washer with each oil change. This ensures a proper seal and prevents leaks. The crush washer is typically included with new oil filters or can be purchased separately.

How to Change the Oil

Changing your oil is a routine maintenance task. Here's a general overview of the steps:

1. Warm Up Engine: Drive the vehicle for a few minutes to warm the oil, allowing it to drain more easily.
2. Lift and Secure: Safely lift the front of the vehicle using a jack and support it with jack stands.
3. Locate Drain Plug: Place a drain pan under the oil pan and remove the drain plug with the appropriate wrench.
4. Drain Oil: Allow all the old oil to drain completely. This can take several minutes.
5. Replace Drain Plug: Install a new crush washer on the drain plug and tighten it to the specified torque (20 ft-lbs / 27 Nm).
6. Replace Oil Filter: Locate and remove the old oil filter. Apply a thin layer of new oil to the gasket of the new filter before threading it on by hand until snug. Then, tighten an additional 3/4 to 1 full turn (or as per filter manufacturer instructions).
7. Add New Oil: Carefully pour the recommended amount and type of new oil into the engine's oil fill cap.
8. Check Level: Start the engine and let it run for a minute, then shut it off and wait a few minutes. Check the oil level on the dipstick and top off if necessary.
9. Reset Oil Life Monitor: Follow your vehicle's specific procedure to reset the oil life monitoring system.
10. Inspect for Leaks: Check for any leaks around the drain plug and oil filter.

Common Issues / Tips

• Engine Stop/Start (ESS) Systems: If your 2020 Jeep Cherokee is equipped with the ESS system, it may place additional stress on the engine oil due to more frequent engine stops and starts. Ensure you are using oil that meets the specified Chrysler MS-6395 standard, as these oils are formulated for better protection under such conditions.
• Oil Filter Location: The oil filter location can vary depending on the engine. For the 2.0L Turbo and 2.4L Tigershark, the filter is typically a canister-style element, often located on top of the engine near the front. The 3.2L Pentastar V6 also uses a canister-style filter, usually located on top of the engine, making it relatively accessible.
• Dealer Consult: For specific OEM part numbers, especially for newer vehicles, it's always best to consult your local Jeep dealer with your VIN to ensure you get the exact part for your vehicle's build.
• Check Owner's Manual: Your owner's manual is the ultimate source for all maintenance information specific to your 2020 Jeep Cherokee. Always double-check specifications and procedures there.

Need an oil change? Find a trusted shop on Repairius.