2019 Jeep Cherokee Oil Capacity & Filter Reference

A 2019 Jeep Cherokee takes between 5 and 6 quarts of oil, depending on the engine. For a definitive answer, you must identify which of the three possible engines your Cherokee has.

Quick Answer

• Oil Capacity (2.0L Turbo): 5.0 quarts / 4.7 liters
• Oil Capacity (2.4L MultiAir): 5.5 quarts / 5.2 liters
• Oil Capacity (3.2L V6): 5.9 quarts / 5.6 liters
• Recommended Oil Weight: 0W-20 (2.4L), 5W-20 (3.2L), or 5W-30 (2.0L Turbo)
• Oil Specification: API SP/SN PLUS (all engines)
• Oil Filter (2.0L Turbo): Mopar 04892339AB (Consult dealer for aftermarket options)
• Oil Filter (2.4L MultiAir): Mopar 04892339AB, Fram CH11665, Wix WL10010, Mobil 1 M1C-456
• Oil Filter (3.2L V6): Mopar 68191349AC, Fram CH11665, Wix WL10010, Mobil 1 M1C-456

Capacity by Engine Option

The 2019 model year Cherokee (KL generation) was available with three different engines. It is critical to identify your engine to ensure you use the correct oil type and fill to the proper capacity.

Note: Always verify the fill level on the dipstick after filling. Add oil slowly to avoid overfilling.

Oil Change Interval

Your Jeep's oil life monitoring system will alert you when it's time for a change. However, the interval can vary based on driving habits.

• Normal Service: Change the oil every 7,500–10,000 miles or 12 months, whichever comes first.
• Severe Service: If you frequently drive in stop-and-go traffic, tow heavy loads, operate in dusty conditions, or make many short trips, you should change the oil every 3,500–5,000 miles.

Drain Plug Torque

Properly tightening the drain plug is crucial to prevent leaks.

• Drain Plug Torque (all engines): 20 ft-lbs (27 N·m)
• Crush Washer: It is highly recommended to replace the drain plug gasket at every oil change to ensure a proper seal. Consult your local dealer for the correct part number.

How to Change the Oil (Brief Steps)

1. Warm the engine slightly to help the oil drain faster.
2. Safely raise and support the vehicle using jack stands.
3. Place a drain pan under the oil pan and remove the drain plug.
4. While the oil is draining, locate and remove the oil filter housing cap (all engines use a cartridge-style filter).
5. Replace the old filter cartridge and the O-rings on the filter cap.
6. Once the oil has finished draining, reinstall the drain plug with a new gasket and torque it to 20 ft-lbs.
7. Lubricate the new filter cap O-ring with fresh oil and screw the cap back into place.
8. Lower the vehicle and fill with the correct amount and type of new oil.
9. Start the engine, let it run for 30 seconds to circulate the new oil, then shut it off and re-check the oil level on the dipstick, topping up as necessary.

Common Issues / Tips

• Oil Consumption (2.4L MultiAir): Some owners of the 2.4L engine have reported higher-than-average oil consumption. It is wise to check your oil level every 1,000 miles to ensure it stays within the safe range on the dipstick.
• Correct Filter: The 2.4L and 3.2L engines use the same popular cartridge oil filter, but the 2.0L Turbo uses a different, less common part. Double-check that you have the correct filter for your specific engine before starting the job.
• O-Rings are Key: Cartridge filters have rubber O-rings on the housing cap that must be replaced with every oil change (the new filter should include them). Forgetting to replace them or pinching one during installation is a common cause of significant oil leaks.

Need an oil change? Find a trusted shop on Repairius.