2016 Jeep Cherokee — Oil Capacity & Filter

The 2016 Jeep Cherokee takes 5.0 quarts (4.7 liters) of 5W-20 oil for both the 2.4L Tigershark I4 and the 3.2L Pentastar V6 engines.

Quick Answer

• Oil Capacity: 5.0 quarts (4.7 liters)
• Recommended Oil Weight: 5W-20
• Oil Type Specification: API SP or a premium quality oil meeting Chrysler MS-6395 standards.
• Oil Filter Part Numbers:
  • 2.4L Tigershark I4:
    • OEM: MOPAR 04892339AA
    • Fram: CH11665
    • Wix: WL10010
  • 3.2L Pentastar V6:
    • OEM: MOPAR 04884877AB
    • Fram: CH11665
    • Wix: WL10010

Capacity by Engine Option

Oil Change Interval

Jeep recommends adhering to the Oil Change Indicator System for optimal maintenance. However, general guidelines are:

• Normal Duty: Up to 10,000 miles or 12 months, whichever comes first.
• Severe Duty: Every 4,000 miles or 6 months, whichever comes first. This applies to conditions such as frequent short trips, extensive idling, towing, dusty environments, or extreme temperatures.

Drain Plug Torque

For both the 2.4L and 3.2L engines, the oil drain plug torque specification is 20 ft-lbs (27 Nm). Always use a new drain plug crush washer with every oil change to ensure a proper seal and prevent leaks. Copper or aluminum crush washers are commonly used.

How to Change the Oil

1. Warm Up Engine & Lift Vehicle: Drive the vehicle for a few minutes to warm the oil, then safely lift and secure the vehicle. Ensure it's level.
2. Locate & Drain: Place a drain pan under the oil pan. Remove the drain plug with a wrench and allow the old oil to fully drain.
3. Replace Drain Plug: Install a new crush washer on the drain plug and re-install it, torquing to 20 ft-lbs (27 Nm).
4. Remove Old Filter: Locate the oil filter (cartridge type for both engines). Use an oil filter wrench to loosen and remove it. Be prepared for some oil to spill.
5. Install New Filter: Lubricate the O-rings of the new filter with fresh oil. Install the new filter and hand-tighten until snug, then give it an additional quarter to half turn. Do not overtighten.
6. Add New Oil: Lower the vehicle. Remove the oil fill cap and add 5.0 quarts of the recommended 5W-20 oil.
7. Check Level & Inspect: Start the engine and let it run for a minute to circulate the new oil. Shut off the engine, wait a few minutes for the oil to settle, then check the dipstick. Top off if necessary.
8. Reset Oil Life Monitor: Follow the procedure in your owner's manual to reset the oil life monitor.

Common Issues / Tips (KL Generation 2014-2020)

• Oil Filter Housing Leaks (3.2L Pentastar V6): A common issue on the 3.2L Pentastar V6 is oil leaks from the oil filter adapter/cooler housing, often manifesting as oil dripping onto the exhaust. This is typically a gasket failure and requires replacement of the housing assembly or its gaskets.
• 2.4L Tigershark Oil Consumption: Some 2.4L Tigershark engines have been known to consume oil. It's crucial to regularly check oil levels between changes to prevent engine damage.
• Cartridge Filter Care: Both engines use a cartridge-style oil filter. Ensure the filter housing cap is properly tightened and the O-rings are correctly seated to prevent leaks.
• Maintain Records: Save your oil change receipts and mileage for service history, especially if oil consumption becomes an issue for the 2.4L engine.

Need an oil change? Find a trusted shop on Repairius.