2015 Nissan Frontier Oil Capacity & Filter

The 2015 Nissan Frontier takes between 3.5 and 4.9 quarts of 5W-30 engine oil, depending on the engine. This article details oil capacities, recommended oil types, filter part numbers, and oil change procedures for your 2015 Frontier.

Quick Answer

• 2.5L 4-Cylinder Engine:

  • Oil Capacity: 3.5 quarts (3.3 Liters)
  • Recommended Oil: 5W-30 API SN or higher, or ILSAC GF-5
  • OEM Oil Filter: Nissan 15208-JA00A
  • Aftermarket Oil Filter Cross-References:
    • Fram: PH6607
    • Wix: 51356
    • Mobil 1: M1-105

• 4.0L V6 Engine:

  • Oil Capacity: 4.9 quarts (4.6 Liters)
  • Recommended Oil: 5W-30 API SN or higher, or ILSAC GF-5
  • OEM Oil Filter: Nissan 15208-65F0E
  • Aftermarket Oil Filter Cross-References:
    • Fram: PH6607
    • Wix: 51356
    • Mobil 1: M1-105

Capacity by Engine Option

Oil Change Interval

Nissan recommends adhering to the following oil change intervals for your 2015 Frontier:

• Normal Duty: Replace engine oil and filter every 5,000 miles or 6 months, whichever comes first.
• Severe Duty: If you operate your Frontier under severe conditions, such as short trips, towing, extensive idling, or dusty environments, it is recommended to change your oil and filter every 3,000 miles or 3 months, whichever comes first.

Drain Plug Torque

The oil drain plug on both the 2.5L 4-cylinder and 4.0L V6 engines of the 2015 Nissan Frontier should be torqued to 25 ft-lbs (34 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. Nissan recommends using a genuine Nissan crush washer, but quality aftermarket alternatives are also available.

How to Change the Oil

1. Warm the Engine: Drive the vehicle for a few minutes to warm up the engine oil, allowing it to drain more easily.
2. Lift and Secure: Safely lift the front of the vehicle using a jack and secure it with jack stands. Ensure the vehicle is level.
3. Locate and Drain: Place a drain pan under the oil pan. Remove the drain plug with a wrench (typically a 14mm or 17mm socket) and allow all the oil to drain completely.
4. Replace Filter: Once the oil has drained, remove the old oil filter using an oil filter wrench. Apply a thin coat of new oil to the gasket of the new filter before screwing it on by hand until snug. Then, tighten an additional 3/4 to 1 turn.
5. Reinstall Drain Plug: Install a new crush washer on the drain plug and thread it back into the oil pan. Torque to 25 ft-lbs (34 Nm).
6. Add New Oil: Lower the vehicle. Locate the oil fill cap on the engine and add the recommended amount and type of new oil (3.5 quarts for 2.5L, 4.9 quarts for 4.0L).
7. Check Level: Start the engine and let it run for a minute. Check for leaks. Turn off the engine, wait a few minutes, and then check the oil level with the dipstick. Add more oil if necessary to reach the "FULL" mark.

Common Issues / Tips

• Oil Filter Location: On both engines, the oil filter is relatively accessible, located on the front of the engine block. However, be prepared for some drips during removal.
• Crush Washer: Do not reuse the old crush washer. It's designed to deform and create a seal, and reusing it can lead to leaks.
• Engine Noise (V6): Some 4.0L V6 engines on the Frontier (and other Nissan vehicles with this engine) can develop a ticking or rattling noise, often attributed to timing chain tensioners or gallery gaskets. While not directly oil-related in terms of capacity or type, regular oil changes with the correct viscosity and specification are crucial for minimizing wear and tear on these components.
• Dipstick Accuracy: Ensure the vehicle is on level ground when checking the oil to get an accurate reading.

Need an oil change? Find a trusted shop on Repairius.