2016 Nissan Frontier — Oil Capacity & Filter
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2016 Nissan Frontier? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Quick answer
The 2016 Nissan Frontier takes between 4.9 and 5.4 quarts of oil, depending on engine.
- Oil capacity (2.5L 4-cyl): 4.9 qts (4.6L) w/ filter
- Oil capacity (4.0L V6): 5.4 qts (5.1L) w/ filter
- Recommended oil weight: 5W-30
- Oil specification: API SN or newer
- OEM oil filter: 15208-65F0E
- Aftermarket oil filters: Fram PH6607, Wix 57356, Mobil 1 M1-108A
Capacity by engine option
| Engine | Liters | Quarts |
|---|---|---|
| 2.5L I-4 | 4.6 | 4.9 |
| 4.0L V-6 | 5.1 | 5.4 |
Oil change interval
Nissan recommends changing the oil in your 2016 Frontier every 5,000 miles or 6 months, whichever comes first. If you frequently tow, drive in dusty conditions, or make short trips, you should follow the severe duty interval of 3,750 miles or 3 months.
Drain plug torque
- Drain plug torque: 25 ft-lbs
- Crush washer: 11026-JA00A (crush washer should be replaced at every oil change to prevent leaks)
How to change the oil
- Warm up the engine to normal operating temperature.
- Remove the oil fill cap.
- Raise the vehicle and place a drain pan under the oil pan.
- Remove the drain plug and allow the oil to drain completely.
- Replace the crush washer and reinstall the drain plug.
- Move the drain pan under the oil filter.
- Remove the oil filter. Be prepared for some oil to spill.
- Apply a light coat of new oil to the gasket of the new oil filter.
- Install the new oil filter and tighten it an additional 2/3 of a turn after the gasket makes contact.
- Fill the engine with the correct amount of new oil.
- Start the engine and check for leaks.
- Turn off the engine and re-check the oil level, topping off as needed.
Common issues / tips
- The 4.0L V6 is known for the plastic timing chain guides to fail. This is a major repair, so it is important to listen for any rattling noises from the front of the engine, especially on cold starts.
- The oil pressure sensor is also a common failure item. If you see the oil pressure gauge reading low or fluctuating, it is important to have it checked out as soon as possible.
- When changing the oil filter, it is a good idea to pre-fill the new filter with fresh oil. This will help to prevent a dry start and ensure that the engine is properly lubricated on startup.
Need an oil change? Find a trusted shop on Repairius.
More specs for the 2016 Nissan Frontier
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2016 Nissan Frontier Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.