2017 Toyota Tacoma Oil Capacity & Filter Reference

The 2017 Toyota Tacoma requires between 5.9 and 6.2 quarts of oil, depending on the engine. The V6 takes slightly more than the 4-cylinder. Always confirm your engine and check the dipstick after filling.

Quick Answer: 2017 Tacoma Oil & Filter Specs

• Oil Capacity (V6): 6.1 qts (5.8 L) with filter change
• Oil Capacity (4-Cyl): 5.9 qts (5.6 L) with filter change
• Recommended Oil Weight: SAE 0W-20
• Oil Specification: API SN / ILSAC GF-5 or higher
• OEM Oil Filter: Toyota 04152-YZZA1 (cartridge style)
• Aftermarket Filter Cross-Reference:
  • Fram: CH9972
  • Wix: WL10010
  • Mobil 1: M1C-251A
• Drain Plug Torque: 30 ft-lbs (40 N·m)
• Drain Plug Gasket: Toyota Part No. 90430-12031

Capacity by Engine Option

The 2017 Tacoma was available with two different engines. The vast majority of trucks are equipped with the 3.5L V6, but the 2.7L 4-cylinder was also an option. Capacities listed are for a full oil and filter change.

Oil Change Interval

Toyota recommends using its synthetic 0W-20 oil for an interval of 10,000 miles or 12 months under normal driving conditions. However, your maintenance schedule may need to be shortened to 5,000 miles or 6 months if you frequently operate the vehicle under "severe duty" conditions. These include:

• Towing or carrying heavy loads
• Extensive idling or low-speed driving (e.g., delivery, police)
• Driving on dusty, muddy, or dirt roads
• Making frequent short trips in temperatures below freezing

Drain Plug Torque

Properly tightening the oil drain plug is critical to prevent leaks.

• Torque Spec: 30 ft-lbs (40 N·m)
• Crush Washer: Always use a new drain plug gasket (crush washer) with every oil change. The OEM part number is 90430-12031. This single-use part is designed to crush and create a perfect seal, preventing leaks and damage to the oil pan threads.

How to Change the Oil (Abbreviated)

Changing the oil on a 2017 Tacoma is straightforward for a DIYer. Both engines use a cartridge-style oil filter, which requires a special tool for the housing cap.

1. Warm Up: Run the engine for a few minutes to warm the oil.
2. Lift & Secure: Safely lift and support the front of the truck with jack stands.
3. Drain Oil: Place a drain pan under the oil pan, remove the 14mm drain plug, and let the oil drain completely.
4. Replace Filter: The oil filter is located under a small access panel on the front skid plate. Use a 64mm oil filter wrench (Toyota tool 09228-06501 or equivalent) to remove the filter housing cap. Remove the old cartridge and two O-rings (one large, one small). Lubricate and install the new O-rings on the housing, then insert the new filter cartridge.
5. Reinstall: Torque the drain plug to 30 ft-lbs with a new gasket. Reinstall the filter housing cap until it is snug.
6. Refill: Add the correct amount of 0W-20 oil through the fill cap on the engine.
7. Check: Start the engine for 30 seconds, then shut it off. Wait a few minutes, then check the dipstick and add oil if necessary to reach the full mark.

Common Issues & Tips for 3rd Gen Tacomas

• Cartridge Filter Housing: The plastic oil filter housing cap can become overtightened and is prone to cracking or breaking. Always use the correct 64mm wrench and avoid overtightening. Many owners upgrade to an all-metal housing (Toyota Part No. 15620-31060) for added durability.
• Special Tools: You will need a specific 64mm, 14-flute oil filter wrench to remove the cartridge housing cap. You will also need a small tool or adapter to drain the residual oil from the filter housing before you remove it, which helps minimize mess.
• Skid Plate Access: Getting to the oil filter requires removing a small access panel or the entire front skid plate. Be prepared with the correct sockets (typically 12mm) to remove these bolts.

Need an oil change? Find a trusted shop on Repairius.