2020 Toyota Tacoma Oil Capacity & Filter Specs

The 2020 Toyota Tacoma with the 3.5L V6 engine takes 5.8 quarts (5.5 liters) of 0W-20 synthetic engine oil. For the 2.7L 4-cylinder engine, it takes 5.5 quarts (5.2 liters) of 0W-20 synthetic engine oil.

Quick answer

3.5L V6 (2GR-FKS) Oil Capacity:

• Oil Capacity: 5.8 quarts (5.5 liters)
• Recommended Oil Weight: 0W-20 Synthetic
• Oil Spec: API SN PLUS or later, or ILSAC GF-5 or later
• OEM Oil Filter Part Number: 90915-YZZD3
• Popular Aftermarket Oil Filter Cross-References:
  • Fram: PH4967
  • Wix: 57047
  • Mobil 1: M1-102

2.7L 4-Cylinder (2TR-FE) Oil Capacity:

• Oil Capacity: 5.5 quarts (5.2 liters)
• Recommended Oil Weight: 0W-20 Synthetic
• Oil Spec: API SN PLUS or later, or ILSAC GF-5 or later
• OEM Oil Filter Part Number: 90915-YZZF2
• Popular Aftermarket Oil Filter Cross-References:
  • Fram: PH4967
  • Wix: 51348
  • Mobil 1: M1-102

Capacity by engine option

Oil change interval

Toyota recommends changing the engine oil and filter on your 2020 Tacoma every 10,000 miles or 12 months, whichever comes first, under normal driving conditions. If you experience severe driving conditions, such as towing, heavy idling, driving in extreme temperatures, or dusty environments, it is advisable to shorten this interval to 5,000 miles or 6 months.

Drain plug torque

For both the 3.5L V6 and 2.7L 4-cylinder engines in the 2020 Toyota Tacoma, the oil pan drain plug torque specification is 30 ft-lbs (40 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. Failure to replace the crush washer can lead to oil weeping around the drain plug.

How to change the oil

1. Warm up the engine: Drive the vehicle for a few minutes to bring the oil to operating temperature, ensuring it drains more easily.
2. Lift and secure: Safely lift the front of the vehicle using a jack and support it with jack stands. This provides adequate clearance to access the drain plug and oil filter.
3. Locate and drain: Place a drain pan underneath the oil pan. Using the correct size wrench, remove the drain plug and allow the old oil to completely drain. Be careful, as the oil may be hot.
4. Replace drain plug: Once drained, clean the drain plug, install a new crush washer, and reinstall the drain plug, tightening it to 30 ft-lbs (40 Nm).
5. Remove oil filter: Position the drain pan under the oil filter housing. Use an oil filter wrench to loosen and remove the old oil filter. Be prepared for some oil to spill.
6. Install new oil filter: Apply a thin film of new engine oil to the rubber gasket of the new oil filter. Screw on the new filter by hand until it's snug, then tighten an additional 3/4 to 1 full turn, or as specified by the filter manufacturer (consult filter packaging for specific instructions).
7. Add new oil: Lower the vehicle. Locate the oil fill cap on top of the engine and remove it. Using a funnel, slowly add the recommended amount of new 0W-20 synthetic oil for your engine (5.8 quarts for the 3.5L V6, 5.5 quarts for the 2.7L 4-cylinder).
8. Check oil level: Replace the oil fill cap. Start the engine and let it run for a few minutes. Turn off the engine and wait for a few minutes to allow the oil to settle. Check the oil level on the dipstick and add more if necessary to reach the "full" mark.
9. Inspect for leaks: Look under the vehicle for any signs of oil leaks around the drain plug and oil filter.

Common issues / tips

• Cartridge-style oil filter: The 2020 Toyota Tacoma uses a cartridge-style oil filter, not a spin-on canister. You will need a special oil filter wrench to remove the cap on the filter housing. Be careful not to overtighten the cap during reinstallation, as it can crack the housing.
• Plastic oil filter housing (some models): Some 2020 Tacomas may have a plastic oil filter housing. If yours is plastic, consider upgrading to an aftermarket aluminum housing for increased durability, especially if you frequently change your own oil. Check your specific vehicle to confirm the material of your oil filter housing.
• Skid plate removal: On many Tacoma models, you will need to remove a skid plate to access the oil drain plug and filter. Have the appropriate tools ready for this.
• Verify oil consumption: It's always a good idea to periodically check your oil level between changes, especially if your truck sees heavy use. Some engines can consume a small amount of oil over time.

Need an oil change? Find a trusted shop on Repairius.