2019 Toyota Tacoma Oil Capacity & Filter

The 2019 Toyota Tacoma with the 2.7L 2TR-FE engine takes 6.1 quarts (5.8 liters) of 0W-20 engine oil, while models equipped with the 3.5L 2GR-FKS engine require 6.2 quarts (5.9 liters) of 0W-20 engine oil.

Quick Answer

2.7L 2TR-FE Engine:

• Oil Capacity: 6.1 quarts (5.8 liters)
• Recommended Oil Weight: 0W-20
• Oil Specification: API SN PLUS / ILSAC GF-5 or higher
• Oil Filter (OEM Part No.): 90915-YZZF2
  • Fram Cross-Reference: PH4967
  • Wix Cross-Reference: 57064
  • Mobil 1 Cross-Reference: M1-102

3.5L 2GR-FKS Engine:

• Oil Capacity: 6.2 quarts (5.9 liters)
• Recommended Oil Weight: 0W-20
• Oil Specification: API SN PLUS / ILSAC GF-5 or higher
• Oil Filter (OEM Part No.): 04152-YZZA1 (cartridge type)
  • Fram Cross-Reference: CH10158
  • Wix Cross-Reference: WL10010
  • Mobil 1 Cross-Reference: M1C-153A

Capacity by Engine Option

Oil Change Interval

Toyota recommends the following oil change intervals for the 2019 Tacoma:

• Normal Duty: Every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: Every 5,000 miles or 6 months, whichever comes first. This applies if you frequently tow, drive in dusty conditions, or make short trips in extreme cold.

Drain Plug Torque

The oil drain plug torque specification for both engines on the 2019 Toyota Tacoma is 30 ft-lbs (41 Nm). Always use a new crush washer with each oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is 90430-12031.

How to Change the Oil

1. Warm up the engine slightly, then park the vehicle on a level surface and engage the parking brake.
2. Place a drain pan large enough to hold the full oil capacity under the drain plug.
3. Remove the oil pan drain plug with a 14mm socket and allow the old oil to drain completely.
4. On 3.5L models, remove the oil filter housing cap using a 64mm 14-flute oil filter wrench. On 2.7L models, spin off the canister-style filter.
5. Replace the old oil filter with a new one. For the 3.5L engine, replace the o-rings on the filter housing cap.
6. Install a new crush washer on the drain plug and re-install it, tightening to 30 ft-lbs (41 Nm).
7. Remove the oil fill cap on the engine.
8. Pour in the recommended amount of new, specific oil (6.1 quarts for 2.7L, 6.2 quarts for 3.5L).
9. Re-install the oil fill cap.
10. Start the engine and let it run for a few minutes to circulate the new oil. Check for leaks around the drain plug and oil filter.
11. Turn off the engine, wait a few minutes for the oil to settle, and check the oil level with the dipstick. Add more oil if necessary.
12. Reset the maintenance reminder.

Common Issues / Tips

• Oil Filter Housing (3.5L): The 3.5L V6 engine uses a cartridge-style oil filter located in a plastic housing. Be careful not to overtighten the housing cap, as it can crack. Always replace the o-rings that come with the new filter element.
• 0W-20 Oil: Both engines are designed to run on 0W-20 synthetic oil for optimal fuel economy and engine protection. Do not deviate from this recommended viscosity.
• Frame Rust (Generational Issue): While not directly related to oil, the 2016-2023 Tacoma (3rd generation) is known for potential frame rust issues. It's a good idea to inspect the frame during your oil change and consider rust prevention measures if you live in an area where road salt is used.
• Maintenance Reminder Reset: After an oil change, you'll need to manually reset the maintenance reminder in your Tacoma. This typically involves using the steering wheel controls and the multi-information display.

Need an oil change? Find a trusted shop on Repairius.