2017 Honda Accord Oil Capacity & Filter
Working on this 2017 Honda Accord? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
The 2017 Honda Accord takes 4.4 quarts (4.2 liters) of 0W-20 engine oil. This applies to both the 2.4L 4-cylinder and the 3.5L V6 engine options.
Quick Answer
- Oil Capacity: 4.4 US Quarts (4.2 Liters)
- Recommended Oil Weight: 0W-20
- Oil Type Specification: API Premium Grade (e.g., API SN or higher, ILSAC GF-5 or higher)
- Oil Filter (OEM):
- 2.4L 4-cylinder: Honda P/N 15400-PLM-A02 or 15400-RTA-003 (consult dealer for latest)
- 3.5L V6: Honda P/N 15400-PLM-A02 or 15400-RTA-003 (consult dealer for latest)
- Oil Filter (Aftermarket Cross-Reference):
- Fram PH7317 (or equivalent Tough Guard TG7317, Ultra Synthetic XG7317)
- Wix 51356 (or equivalent XP 51356)
- Mobil 1 M1-110
Capacity by Engine Option
| Engine | Oil Capacity | Oil Type |
|---|---|---|
| 2.4L 4-Cylinder | 4.4 Quarts (4.2 Liters) | 0W-20 |
| 3.5L V6 | 4.4 Quarts (4.2 Liters) | 0W-20 |
Oil Change Interval
Honda recommends following the Maintenance Minder system displayed on your dashboard. This system dynamically calculates oil life based on driving conditions and engine operation. Generally, oil change intervals can range:
- Normal Duty: 7,500 – 10,000 miles or 12 months, whichever comes first.
- Severe Duty (e.g., frequent short trips, extreme temperatures, towing, dusty conditions): 3,000 – 5,000 miles or 6 months, whichever comes first. The Maintenance Minder will likely indicate a shorter interval under these conditions.
Always refer to your vehicle's owner's manual for the most accurate and up-to-date maintenance schedules.
Drain Plug Torque
The oil drain plug for the 2017 Honda Accord (both 2.4L and 3.5L engines) should be torqued to 29 lb-ft (39 N·m). It is highly recommended to replace the crush washer (typically 14mm) with a new one every time the oil is changed to ensure a proper seal and prevent leaks. Honda crush washer P/N: 94109-14000 (confirm with dealer).
How to Change the Oil
- Warm Up Engine: Run the engine for a few minutes to bring the oil to operating temperature, ensuring it drains more completely.
- Lift and Secure: Safely lift the front of the vehicle using a jack and secure it with jack stands on a level surface.
- Locate Drain Plug: Place a drain pan underneath the oil pan. Locate the drain plug on the bottom of the oil pan.
- Drain Oil: Carefully loosen and remove the drain plug with a wrench (typically a 17mm or 19mm socket). Allow all the old oil to drain completely.
- Replace Crush Washer & Plug: Install a new crush washer on the drain plug and reinsert it into the oil pan. Torque to 29 lb-ft (39 N·m).
- Remove Oil Filter: Locate the oil filter (usually near the front of the engine, accessible from below or ऊपर). Use an oil filter wrench to loosen it, then remove it by hand. Be prepared for some oil to spill.
- Prepare New Filter: Apply a thin film of new oil to the rubber gasket of the new oil filter.
- Install New Filter: Hand-tighten the new oil filter until the gasket makes contact, then turn an additional 3/4 to 1 full turn. Do not overtighten.
- Add New Oil: Lower the vehicle. Remove the oil filler cap on top of the engine and pour in the specified amount of new 0W-20 oil (4.4 quarts).
- Check Level: Start the engine and let it run for a minute to circulate the oil. Shut off the engine, wait a few minutes, then check the oil level with the dipstick. Add more oil if necessary, ensuring it
Need service on your Honda Accord?
Your vehicle and question are already filled in — just add your location.
More specs for the 2017 Honda Accord
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2017 Honda Accord Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.
Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-06-26.