Working on this vehicle? Write estimates, send inspections & invoice customers from your phone.

    Start 14-Day Free Trial
    ← All vehicle specs
    Torque Specifications

    2021 Honda Accord — Torque Specifications

    Everything on this vehicle

    Key fastener torque values for wheels, engine, transmission, and brakes

    Working on this 2021 Honda Accord? Run just this one job through Repairius.

    No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.

    14-day free trial · credit card required · cancel anytime

    Quick answer — 2021 Honda Accord

    Wheel lug nuts
    80–90 ft-lb / 108–122 Nm
    Engine oil drain plug
    25–33 ft-lb / 34–45 Nm
    Transmission drain plug
    29–36 ft-lb / 39–49 Nm
    Front brake caliper bracket bolts
    72–94 ft-lb / 98–127 Nm

    From the table below. Confirm with your owner's manual for your exact engine.

    2021 Honda Accord — Torque Specifications

    Quick reference

    FastenerTorque (ft-lb / Nm)Notes
    Wheel lug nuts80–90 ft-lb / 108–122 Nm5-lug hub; torque in a star pattern and recheck after 50–100 miles.
    Engine oil drain plug25–33 ft-lb / 34–45 NmUse new crush washer; aluminum oil pan.
    Transmission drain plug29–36 ft-lb / 39–49 NmVaries by trans: CVT (HCF-2), 10‑speed AT (ATF‑Type 3.1), e‑CVT hybrid. Verify by trans code.
    Front brake caliper bracket bolts72–94 ft-lb / 98–127 NmBy trim/rotor size; clean threads, apply medium threadlocker if specified.
    Rear brake caliper bracket bolts60–80 ft-lb / 81–108 NmParking brake style may vary (hybrid vs. gas).
    Brake caliper slide pins17–26 ft-lb / 23–35 NmLight silicone brake grease on pin bushings; do not over‑torque.
    Front axle nut (drive shaft)180–245 ft-lb / 244–332 NmStaked nut; torque on the ground, then stake. Range covers 1.5T/2.0T/Hybrid.
    Spark plugs (gas engines)13–18 ft-lb / 17–24 Nm1.5T L15BE and 2.0T K20C4; tighten to spec on clean, dry threads unless plug maker says otherwise.
    Valve cover (rocker/plug well cover) bolts7–9 ft-lb / 9–12 NmSnug in criss‑cross sequence; do not compress gasket excessively.
    Intake manifold bolts/nuts16–22 ft-lb / 22–30 NmTorque in OEM sequence, in stages (center‑out).

    Note: Use ranges where multiple submodels (1.5T, 2.0T, and Hybrid) or hardware variations exist. Always confirm against the exact VIN/engine/transmission in the OEM service manual.

    Wheel lug torque pattern

    • Pattern: For the Accord’s 5‑lug hubs, use a star/cross pattern (1‑3‑5‑2‑4).
    • Steps: Bring all lugs to hand‑tight, torque to ~50% of final spec in pattern, then to full spec in the same pattern.
    • Re‑torque: After 50–100 miles of driving on newly installed wheels or after brake work.

    Brake torque notes

    • Bracket vs. slider bolts: The bracket (anchor) bolts generally require substantially higher torque than the caliper slide pins. Mixing these specs is a common cause of loose calipers or stripped pins.
    • Clean and prep: Wire‑brush rust from bracket threads and hub faces. Replace single‑use hardware if specified. Use medium‑strength threadlocker only where OEM calls for it.
    • Lubrication: Apply high‑temp silicone brake grease to slide pin bodies and boots—never to pad friction surfaces or rotor. Keep grease off bracket bolt threads unless OEM specifies it.
    • Final checks: After reassembly, pump the brake pedal to seat the pads before moving the vehicle. Verify rotor turns freely (no drag) and that flexible hoses are not twisted.

    Why torque matters

    Correct torque keeps clamp loads within design limits so parts don’t loosen, distort, or fail. Under‑torque can let joints shift (leading to noise, pulsation, or wheel loss), while over‑torque can stretch fasteners, crack aluminum housings, warp rotors, or crush gaskets. Using a calibrated torque wrench, clean threads, correct washers/gaskets, and the proper sequence ensures reliable sealing (oil/trans drains, intake), consistent brake performance (bracket/slider bolts), and safe driveline operation (axle nuts).

    Additional guidance for the 2021 Accord

    • Engines/transmissions: The 2021 Accord was offered as 1.5L turbo (CVT), 2.0L turbo (10‑speed automatic), and Hybrid (e‑CVT). Torque values can vary slightly by powertrain and rotor/caliper package; use the range above and verify per your VIN.
    • Sealing washers: Always replace aluminum crush washers on engine oil and most transmission drain plugs. Inspect mating surfaces for gouges.
    • Axle nuts: Set vehicle on the ground (or simulate ground load with a helper bar against the hub) for final torque. Install new axle nut and stake into the shaft groove after torquing. Recheck after short road test if any bearing/hub work was performed.
    • Spark plugs: Use the exact heat range and gap per under‑hood label. If using anti‑seize (often not recommended by plug makers), reduce applied torque accordingly.
    • Intake manifold: Torque in two to three stages from the center outward to avoid vacuum leaks and plastic/composite warpage where applicable.

    Disclaimer: These specifications are provided for reference. Critical fasteners should always be confirmed in the OEM Honda service manual for your exact trim and drivetrain.

    Find a trusted shop on Repairius.

    Need service on your Honda Accord?

    Your vehicle and question are already filled in — just add your location.

    More specs for the 2021 Honda Accord

    Oil Capacity & Filter

    Capacity, weight, filter PN, drain plug torque, change interval.

    Fluid Type Specs

    Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.

    Coolant Capacity & Type

    Total system capacity, OEM coolant spec, flush interval, bleed tips.

    Transmission Fluid & Service

    Trans model, fluid spec, capacity, filter PN, service interval.

    Brake Pad & Rotor Specs

    Pad PNs, rotor size, min thickness, caliper torque.

    Tire Size & Pressure

    OEM size, cold psi, bolt pattern, wheel size, TPMS.

    Battery Size & Group

    Group size, CCA, AGM/flooded, dimensions, reset note.

    A/C Refrigerant & Oil

    R-134a or R-1234yf, charge oz, PAG oil spec.

    Bulb Sizes (Headlight, Tail, Fog)

    Headlight, fog, tail, turn, reverse, interior.

    Factory Maintenance Schedule

    Service intervals by mileage, severe-duty notes, known issues.

    Towing Capacity & Payload

    Max tow, payload, GVWR/GCWR, hitch class by trim.

    Fuse Box Diagram & Amperage

    Fuse box locations, layout, amps, and what each fuse controls.

    Serpentine Belt Routing & Length

    Belt routing, length, rib count, OEM + aftermarket PNs.

    Wheel Alignment Specifications

    Camber, caster, toe ranges (front & rear), adjustability notes.

    Paint Color Codes

    All factory colors with paint codes, sticker location, touch-up tips.

    Wiper Blade Sizes

    Driver/passenger/rear blade size, attachment, OEM + cross-refs.

    Spark Plug Type & Gap

    Plug PN, gap, torque, interval by engine.

    Transmission & Axle Gear Ratios

    Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.

    Key Fob Programming

    DIY programming steps, FCC ID, fob PN, battery, transponder.

    Same spec — other model years

    Maintenance & repair guides

    Browse by make

    Running an auto or diesel repair shop?

    Compare Repairius to the shop software you're paying for

    $99.99/month (first location included), unlimited users, 14-day free trial.

    Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-07-12.

    Run your shop from estimate to payment

    Don't overhaul your shop. Test Repairius on your next job.

    Repairius keeps estimates, work orders, real-time job assignment, customer and vehicle history, inventory, and payments in one place — on desktop and in your pocket.

    14-day free trial · credit card required · cancel anytime

    Not a mechanic? Send Repairius to your shop — they can run estimates, jobs, and invoices in one place.

    Know someone who needs this?

    Share this page with a mechanic, a shop owner, or a friend working on the same problem.

    Know a mechanic or shop owner Repairius could help?

    Send them Repairius in one tap. Free listing, online booking, reminders and the full shop workflow.

    Text them Email