2022 Jeep Cherokee Oil Capacity & Filter Specs

The 2022 Jeep Cherokee takes between 5.0 and 5.9 quarts of oil depending on the engine equipped, with the popular 3.2L V6 requiring 5.9 quarts of 5W-20. As an ASE-certified master technician, I regularly service the KL-generation Cherokee, and keeping up with the exact oil capacity and specifications is critical for maintaining Chrysler’s powertrain warranty and preventing premature wear, especially on the V6 and turbo models.

Quick answer

For the most common engine—the 3.2L Pentastar V6—here are your quick reference specs:

• Oil Capacity: 5.9 quarts (5.6 liters) with filter change.
• Recommended Weight: 5W-20.
• Oil Specification: API SP / ILSAC GF-6A, Chrysler Material Standard MS-6395.
• Oil Filter (OEM): Mopar MO-349 (Part # 68191349AC)
• Oil Filter (Aftermarket): Wix WL10010, Fram CH11665, Mobil 1 M1C-254A.

(Note: Filter numbers above are for the 3.2L V6 cartridge. The 2.0L and 2.4L engines use a spin-on style filter, Mopar MO-339).

Capacity by engine option

The 2022 Jeep Cherokee was offered with three distinct engine options. Ensure you know which engine is under your hood before buying your oil.

Oil change interval

Jeep uses an automatic Oil Life Monitor system that alerts you when it's time for a change, but you should never exceed the maximum manual intervals.

• Normal Duty: Up to 10,000 miles or 12 months, whichever comes first. (Following the dashboard indicator).
• Severe Duty: 4,000 to 5,000 miles or 6 months. Severe duty applies if you frequently tow, drive off-road, idle extensively, or primarily take short trips (under 5 miles) in freezing temperatures.

Drain plug torque

• Torque specification: 20 ft-lbs (27 Nm).
• Crush washer note: The factory drain plug features an integrated rubber O-ring seal. If this seal is cracked, flattened, or torn, you must replace the entire drain plug, as the seal is not sold separately by Mopar. Avoid over-tightening, as the aluminum oil pans on these engines are easily stripped.

How to change the oil

1. Warm the engine: Run the engine for a few minutes to bring the oil to operating temperature, allowing it to drain faster and suspend contaminants.
2. Access the filter: For the 3.2L V6, the cartridge oil filter housing is located on top of the engine under the plastic cover. Use a 24mm socket to loosen the cap. Do this before draining the oil so the filter housing can drain into the pan.
3. Drain the oil: Safely raise the vehicle. Locate the 13mm drain plug on the oil pan. Place a catch pan underneath and remove the plug.
4. Replace the filter: Swap the old paper cartridge with your new one. Seat the new O-ring on the plastic cap, lubricate it with clean oil, and torque the cap to 18 ft-lbs (25 Nm). (For 2.0L/2.4L, replace the spin-on filter underneath).
5. Reinstall drain plug: Wipe the mating surface clean, inspect the plug's rubber seal, and torque the plug to 20 ft-lbs.
6. Refill and verify: Add the required amount of fresh oil. Start the engine, let it run for 30 seconds to fill the filter, shut it off, and check the dipstick after 5 minutes to ensure the level is perfect.
7. Reset the oil light: Turn the ignition to the ON position (without starting the engine). Slowly depress the accelerator pedal to the floor three times within 10 seconds. Turn the ignition off.

Common issues / tips

For the KL-generation Cherokee, a frequent issue with the 3.2L V6 is cracking the plastic oil filter housing cap. It is incredibly easy to overtighten. Use a proper 24mm 6-point socket and never exceed 18 ft-lbs of torque. Additionally, the 2.4L Tigershark engines are notorious for oil consumption. If you own the 2.4L, check your dipstick every 1,000 miles between changes; running it low can lead to catastrophic internal damage. Always use full synthetic oil to protect the variable valve timing components across all engine options.

Need an oil change? Find a trusted shop on Repairius.