2022 Kenworth W900 — Coolant Capacity & Type
Capacity, coolant spec, mix ratio, intervals, refill/bleed tips, and common issues
Working on this 2022 Kenworth W900? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
The 2022 Kenworth W900 holds roughly 50–65 quarts (47–61 liters) of coolant in total, depending on engine (Cummins X15 vs PACCAR MX-13), radiator/heater configuration, and auxiliary circuits.
Quick answer
- Total cooling system capacity: about 50–65 qt (47–61 L), verify on the under‑hood label or chassis spec sheet
- OEM coolant spec: Heavy‑duty extended‑life OAT (red) coolant. Kenworth/PACCAR factory fill is a red, silicate‑free, phosphate‑free OAT ELC that meets HD requirements such as ASTM D6210 and TMC RP 329/330. Cummins and PACCAR both approve HD OAT ELCs per their current specifications (check the jug for explicit Cummins/PACCAR approvals).
- Mix ratio: 50/50 premix (or 50/50 concentrate with deionized/distilled water) for –34°F (–37°C) protection. Up to 55–60% concentrate is acceptable in extreme cold; never exceed 60%.
Capacity by engine option
- Cummins X15 (14.9L): typically 55–65 qt (52–61 L) total depending on radiator size, heater/sleeper circuits, and wheelbase plumbing
- PACCAR MX‑13 (12.9L): typically 50–60 qt (47–57 L) total depending on cooling package and HVAC circuits
Note: Actual capacity varies with cooling module size, number of heater cores (cab/sleeper), transmission and EGR cooler plumbing, and any APUs or aftermarket heaters. Always measure what drains out and verify with build records.
Flush interval
- Normal service (line‑haul/highway with HD OAT ELC): 600,000–1,000,000 miles (960,000–1,600,000 km) or 6–8 years, whichever comes first, with periodic coolant condition checks (freeze point, pH, and contamination). Some NOAT coolants specify an extender at mid‑life—follow the coolant manufacturer’s label.
- Severe duty (vocational, high‑dust, frequent idling, extreme heat/cold, or frequent top‑offs with make‑up water): 300,000–500,000 miles (480,000–800,000 km) or 3–5 years. Test more frequently and shorten intervals if contamination or mixing is suspected.
Important: Do not mix OAT/ELC with conventional green IAT coolants or add SCAs unless the coolant maker/engine OEM specifically permits it. Mixing types shortens service life and can cause gel/sludge.
How to refill & bleed
- Preparation: Park level, set brake, and allow the engine to cool. Open the heater control valves so cab/sleeper cores fill during service.
- Drain: Open the radiator drain (petcock or lower hose) and the engine block drains (Cummins X15 typically has block drains on the right side; MX‑13 has a block drain as well). Capture and dispose of coolant properly.
- Flush (if servicing): Close drains, fill with clean water, run to operating temp with heater on, cool, and drain. Repeat until clear. Use a compatible chemical flush only if required by OEM/coolant maker.
- Close all drains and clamps. Inspect hoses, clamps, surge tank, and cap. Replace weak caps; HD systems rely on correct cap pressure.
- Refill method:
- Preferred: Use a vacuum‑fill tool at the surge/degassing tank to pull 20–25 inHg and ingest 50/50 premix. This minimizes trapped air in the EGR cooler and heater circuits.
- Alternate: Slow fill through the surge tank to the “COLD” mark. Pause periodically to allow deaeration via the small return/bleed hose.
- Initial bleed: With the cap off, start the engine and idle at 1,000–1,100 rpm. Watch for steady return flow into the surge tank. Top up as the level drops. Once the thermostat opens and upper radiator hose is hot, install the cap.
- Warm‑up and recheck: Bring to operating temperature, verify heater performance, and check for leaks. After cool‑down, recheck level and top off to the “COLD” mark.
- Post‑service: After the first long drive under load, recheck level again. Test freeze point and nitrite level only if using a nitrited OAT.
Notes specific to this platform:
- Most W900 cooling packs use a deaeration/return line to the surge tank and do not require a manual bleed screw. Some EGR coolers may have a high‑point plug—use per engine manual if opened.
- Always maintain the small bleed hose from the high point to the surge tank; kinks here cause chronic air pockets and overheat complaints.
Common cooling system issues on W900 (this generation)
- Radiator or charge‑air cooler stack clogging with debris/bugs, reducing airflow; periodic cleaning of the cooling module is critical for line‑haul units.
- Radiator tank seam seepage and hose‑to‑neck leaks, especially on high‑vibration vocational specs.
- Surge tank cap fatigue leading to low system pressure, boil‑over, or nuisance level warnings; replace caps proactively.
- Coolant level sensor faults causing false warnings due to contamination or sensor aging; clean/replace as needed.
- Water pump seepage and thermostat wear on high‑mileage X15/MX‑13 engines; look for dried coolant trails at the weep hole and around the housing.
- Heater control valve and sleeper heater hose leaks near the frame rails or at bulkhead fittings; inspect for chafe points.
- EGR cooler and related plumbing leaks; small losses can aerate the system and cause intermittent overheat.
- Coolant chemistry mix‑ups after roadside top‑offs; mixing OAT with conventional coolant shortens ELC life and can gel—test and correct by full exchange if mixed.
Find a trusted shop on Repairius.
Need service on your Kenworth W900?
Your vehicle and question are already filled in — just add your location.
More specs for the 2022 Kenworth W900
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2022 Kenworth W900 Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.
Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-10-06.