2016 Nissan Titan Oil Capacity & Filter

The 2016 Nissan Titan with the 5.6L V8 engine takes 7.3 quarts (6.9 Liters) of 0W-20 engine oil.

Quick Answer

• Oil Capacity: 7.3 quarts (6.9 Liters)
• Recommended Oil Weight: 0W-20
• Oil Specification: API SN or later, ILSAC GF-5 or later
• OEM Oil Filter Part Number: Nissan 15208-8990F (Consult dealer for latest revision)
• Aftermarket Oil Filter Cross-References:
  • Fram: PH6607
  • Wix: 51356
  • Mobil 1: M1-108

Capacity by Engine Option

For the 2016 model year, the Nissan Titan was available with a single engine option:

Oil Change Interval

Adhering to the manufacturer's recommended oil change intervals is crucial for the longevity of your 2016 Nissan Titan's engine.

• Normal Duty: Under normal driving conditions, it is recommended to change your oil and filter every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: If you operate your Titan under severe driving conditions, such as frequent towing, off-road driving, extreme temperatures, or extensive idling, the oil change interval should be shortened to every 5,000 miles or 6 months, whichever comes first.

Drain Plug Torque

The drain plug on your 2016 Nissan Titan requires a specific torque to ensure a proper seal without overtightening, which can strip the threads. The recommended torque for the drain plug is 25 lb-ft (34 Nm). Always replace the crush washer with a new one during each oil change to prevent leaks. The crush washer helps create a tight seal and is designed for single use.

How to Change the Oil

Changing the oil in your 2016 Nissan Titan is a straightforward process for the DIY enthusiast. Here's a simplified guide:

1. Warm Up Engine: Drive the vehicle for a few minutes to bring the oil to operating temperature, ensuring it drains more easily.
2. Lift and Secure: Safely lift the front of the vehicle using jack stands or a ramp.
3. Locate Drain Plug: Place a drain pan directly underneath the oil pan drain plug.
4. Drain Oil: Carefully remove the drain plug (using a 14mm socket) and allow the old oil to drain completely. Be mindful of hot oil.
5. Replace Drain Plug: Once all oil has drained, install a new crush washer and reinstall the drain plug, torquing it to 25 lb-ft (34 Nm).
6. Remove Oil Filter: Locate the oil filter (typically on the passenger side of the engine, behind the front wheel well) and remove it using an oil filter wrench. Be prepared for a small amount of oil to spill.
7. Install New Filter: Apply a thin film of new oil to the rubber gasket of the new oil filter. Screw on the new filter by hand until snug, then tighten an additional 3/4 to 1 full turn (or follow filter manufacturer instructions).
8. Add New Oil: Lower the vehicle. Remove the oil cap and carefully pour in 7.3 quarts of the recommended 0W-20 oil.
9. Check Level: Start the engine and let it run for a few minutes to circulate the new oil. Shut off the engine, wait 5-10 minutes, and then check the oil level using the dipstick. Add more oil if necessary to reach the "FULL" mark.
10. Reset Maintenance Light: Follow the instructions in your owner's manual to reset the oil maintenance light.

Common Issues / Tips

• VK56VD Engine Piston Slap/Tick: While not directly related to oil capacity, some owners of the VK56VD engine may experience a piston slap or ticking noise. Using the correct weight and specification of oil (0W-20 API SN/ILSAC GF-5 or later) and adhering to regular change intervals can help maintain optimal engine lubrication and potentially mitigate such noises, though it may not be a cure for mechanical issues.
• Oil Filter Location: The oil filter on the 2016 Titan's 5.6L V8 is located in a somewhat recessed area, which can make it a bit challenging to access without the right tools (a suitable oil filter wrench is highly recommended).
• Gasket Maintenance: Always ensure the oil filter gasket is properly seated and the drain plug crush washer is replaced with each oil change to prevent leaks.

Need an oil change? Find a trusted shop on Repairius.