2017 Nissan Titan Oil Capacity & Filter

The 2017 Nissan Titan takes 6.5 quarts (6.1 liters) of 0W-20 oil for the 5.6L V8 engine. This applies to both the Titan and Titan XD models equipped with the 5.6L Endurance V8.

Quick Answer

• Oil Capacity: 6.5 quarts (6.1 liters)
• Recommended Oil Weight: 0W-20
• Oil Type Specification: API SN or later, ILSAC GF-5 or later
• OEM Oil Filter Part Number: 15208-8Y00C
• Aftermarket Oil Filter Cross-References:
  • Fram: PH10060
  • Wix: 57060
  • Mobil 1: M1-110

Capacity by Engine Option

The 2017 Nissan Titan and Titan XD (non-Cummins diesel) were offered with a single engine option, the 5.6L Endurance V8.

Oil Change Interval

Nissan recommends the following oil change intervals for the 2017 Titan:

• Normal Duty: Every 10,000 miles or 12 months, whichever comes first.
• Severe Duty: Every 5,000 miles or 6 months, whichever comes first. Severe duty conditions include frequent short trips, towing, extensive idling, dusty conditions, or extreme temperatures.

Drain Plug Torque

The oil drain plug for the 2017 Nissan Titan (5.6L V8) should be torqued to 25 ft-lbs (34 Nm). Always replace the crush washer with a new one to prevent leaks. The crush washer helps create a reliable seal and is designed to deform once, so reusing it can lead to drips or even significant leaks.

How to Change the Oil

Changing the oil on your 2017 Nissan Titan is a straightforward process:

1. Preparation: Park on a level surface, engage the parking brake, and allow the engine to cool slightly. Gather your tools: wrench for the drain plug, oil filter wrench, drain pan, new oil, new oil filter, and a new crush washer.
2. Drain Oil: Place the drain pan under the oil pan. Using the correct size wrench, remove the drain plug and allow the old oil to drain completely. Inspect the old crush washer and dispose of it.
3. Replace Drain Plug: Install the new crush washer onto the drain plug and reinsert the drain plug. Torque to 25 ft-lbs (34 Nm).
4. Remove Oil Filter: Position the drain pan under the oil filter. Use an oil filter wrench to loosen and remove the old oil filter. Be prepared for some residual oil to spill.
5. Install New Oil Filter: Apply a thin coat of new oil to the rubber gasket of the new oil filter. Screw on the new filter by hand until snug, then tighten an additional 3/4 to 1 full turn. Consult the filter packaging for specific tightening instructions.
6. Add New Oil: Remove the oil filler cap on the engine. Slowly add the recommended amount of new 0W-20 oil (6.5 quarts)..
7. Check Level & Inspect for Leaks: Start the engine and let it run for a few minutes to circulate the new oil. Turn off the engine, wait a few minutes for the oil to settle, then check the dipstick. Top off if necessary. Inspect the drain plug and oil filter area for any leaks.
8. Reset Maintenance Light: Follow your owner's manual instructions to reset the oil life monitor.

Common Issues / Tips

• Oil Consumption: Some owners have reported minor oil consumption, especially in early production models of the 5.6L Endurance V8. Keep an eye on your oil level between changes and top off as needed.
• Oil Filter Location: The oil filter is easily accessible from underneath the vehicle, making changes relatively simple.
• Choosing the Correct Oil: Always use the recommended 0W-20 weight and ensure it meets or exceeds the API SN and ILSAC GF-5 (or later) specifications to protect your engine and maintain your warranty.
• Crush Washer is Critical: As mentioned, always replace the drain plug crush washer. It's a small, inexpensive part that prevents messy and potentially damaging oil leaks.

Need an oil change? Find a trusted shop on Repairius.