2015 Nissan Titan — Oil Capacity & Filter Specs

The 2015 Nissan Titan 5.6L V8 (VK56DE) takes 6.9 quarts (6.5 liters) of engine oil with a filter change.

Quick answer

• Capacity (with filter): 6.9 qt (6.5 L)
• Recommended viscosity: SAE 5W-30 for most climates
• Oil specification: API SN or newer (SP acceptable), ILSAC GF-5/6A; Nissan Genuine 5W-30 is approved
• Oil filter:
  • OEM Nissan: 15208-65F0E (supersessions may apply; confirm with dealer if needed)
  • Popular aftermarket cross-refs: Fram XG7317/PH7317, WIX 57356, Mobil 1 M1-110A

Capacity by engine option

Oil change interval

• Normal service: Every 7,500 miles (12,000 km) or 12 months, whichever comes first, using API SN/SP quality oil.
• Severe service: Every 5,000 miles (8,000 km) or 6 months. Severe use includes frequent towing/hauling, repeated short trips under 5 miles, extensive idling, dusty/off-road operation, or very hot/cold climates.

Tip: If your Titan sees mixed duty with regular towing or off-road use, treat it as severe service. Follow the maintenance minder/indicator if equipped, but do not exceed 12 months between oil changes.

Drain plug torque

• Drain plug torque: 25 ft-lb (34 N·m)
• Crush washer: Replace the aluminum gasket at each service to prevent seepage. Nissan’s common 14 mm drain plug washer is widely available; consult your dealer/parts source if unsure of the correct washer for your VIN.

How to change the oil

1. Warm the engine to operating temp, then shut it off and set the truck on level ground. Chock wheels.
2. If equipped with a skid plate/splash shield, remove the access panel or the plate to reach the drain plug and filter.
3. Place a drain pan, remove the drain plug, and allow oil to drain completely. Replace the crush washer and torque the plug to 25 ft-lb (34 N·m).
4. Move the drain pan under the oil filter (passenger side front of engine). Spin off the old filter. Use a bag or foil to control spill.
5. Lightly oil the new filter’s gasket with fresh oil. Install by hand until the gasket contacts the base, then tighten 3/4 turn by hand (do not use a wrench unless specified by the filter maker).
6. Add 6.5 quarts of 5W-30, wait a minute, start the engine, and check for leaks. Shut off, wait 5 minutes, and check the level.
7. Top up to the dipstick’s full mark; total fill is typically 6.9 quarts with filter. Reinstall any shields/skid plates.
8. Reset the maintenance reminder (if equipped) and properly recycle the used oil/filter.

Common issues / tips for this generation Titan (2004–2015)

• Exhaust manifold leaks: A tick on cold start is common due to cracked manifolds. Not an oil issue, but it’s a good time to inspect while you’re under the truck.
• Oil cooler adapter O-ring seepage: The VK56DE uses an oil cooler/adapter at the filter mount. If you notice oil residue around the filter base or cooler lines, the O-ring may be flattening with age—replace the seal to prevent drips.
• Skid plate clearance: PRO-4X and trucks with aftermarket skid plates can have tight access around the filter. Verify your chosen filter length clears the plate; the listed cross-refs are common fits.
• Filter size note: Nissan has used both “short” and “long” M20×1.5 filters on various models. The Titan typically accepts the longer 7317-size can listed above. Always ensure gasket diameter and clearance are correct for your truck.
• Keep it 5W-30: While 10W-30 may appear in some older charts for warmer climates, Nissan’s preferred fill for the 2015 Titan is 5W-30 meeting API gasoline specs.
• Dipstick technique: Check level on level ground, fully warmed, after a 5-minute wait. Overfilling can aerate the oil at highway speeds—aim for the top mark without exceeding it.

Need an oil change? Find a trusted shop on Repairius.