2019 Toyota Camry Oil Capacity & Filter Specs

The 2019 Toyota Camry takes 4.8 quarts (4.5 liters) of 0W-20 synthetic oil for both the 2.5L 4-cylinder and the 3.5L V6 engines.

Quick Answer

• Oil Capacity: 4.8 quarts (4.5 Liters)
• Recommended Oil Weight: 0W-20 Synthetic
• Oil Specification: API SN PLUS or later (or ILSAC GF-5 or later)
• OEM Oil Filter: Toyota P/N 90915-YZZF2 (for 2.5L and 3.5L)
• Aftermarket Oil Filter Cross-References:
  • Fram: CH12060 (for 2.5L and 3.5L)
  • Wix: 57064 (for 2.5L and 3.5L)
  • Mobil 1: M1C-251A (for 2.5L and 3.5L)

Capacity by Engine Option

Oil Change Interval

For the 2019 Toyota Camry, regular oil changes are crucial for engine longevity.

• Normal Duty Driving: Toyota recommends an oil change every 10,000 miles or 12 months, whichever comes first. This applies to vehicles primarily driven in moderate conditions.
• Severe Duty Driving: If your driving conditions fall under "severe duty," Toyota recommends an oil change every 5,000 miles or 6 months, whichever comes first. Severe duty conditions include:
  • Frequent short trips (less than 5 miles in cold weather or 1 mile in freezing weather).
  • Towing, carrying heavy loads, or driving on dusty roads.
  • Extensive idling or stop-and-go driving.
  • Driving in extremely cold or hot temperatures.

Always consult your owner's manual for the most accurate and up-to-date maintenance schedule for your specific vehicle.

Drain Plug Torque

The oil drain plug on the 2019 Toyota Camry should be torqued to 30 ft-lbs (40 Nm). It is highly recommended to replace the crush washer with a new one every time you perform an oil change to ensure a proper seal and prevent leaks. The OEM crush washer part number is 90430-120310.

How to Change the Oil

Changing the oil on your 2019 Toyota Camry is a straightforward process for the DIY mechanic. Always ensure the vehicle is on a level surface and supported securely by jack stands.

1. Gather Supplies: New oil, oil filter, drain pan, wrench for drain plug, oil filter wrench, new crush washer, and rags.
2. Warm Up Engine (Slightly): Run the engine for a few minutes to warm the oil, allowing it to drain more easily. Do not perform an oil change on a hot engine.
3. Locate Drain Plug: Place the drain pan underneath the oil pan. Use a wrench to carefully remove the drain plug and allow all the old oil to drain.
4. Remove Old Filter: Once the oil has drained, locate the oil filter. Use an oil filter wrench to remove it. Be prepared for a small amount of oil to spill from the filter.
5. Install New Filter: Apply a thin coat of new oil to the rubber gasket of the new oil filter. Screw on the new filter by hand until it's snug, then tighten it an additional 3/4 to 1 full turn (or according to filter manufacturer recommendations).
6. Replace Drain Plug: Install the new crush washer on the drain plug and reinstall it into the oil pan. Torque to 30 ft-lbs (40 Nm).
7. Add New Oil: Carefully pour the recommended amount and type of new oil into the engine's oil fill cap.
8. Check Oil Level: Start the engine and let it run for a minute or two. Turn off the engine, wait a few minutes for the oil to settle, then check the oil level with the dipstick. Add more oil if necessary, but be careful not to overfill.
9. Reset Maintenance Light: Consult your owner's manual for instructions on how to reset the oil maintenance light on your dash.

Common Issues / Tips

• Oil Filter Housing: The 2019 Toyota Camry uses a cartridge-style oil filter located in a plastic housing. Be careful not to overtighten this housing, as it can be prone to cracking if excessive force is used. The torque specification for the oil filter housing cap is typically 18 ft-lbs (25 Nm). It's also a good idea to lubricate the O-rings on the filter housing cap with new oil before reinstallation.
• Engine Undershield (Splash Guard): You will likely need to remove a portion of the plastic undershield or splash guard to access the oil drain plug and filter. These are typically held in place with a series of plastic clips and screws.
• Genuine Toyota Parts: While aftermarket filters are available and often acceptable, many enthusiasts and technicians prefer using genuine Toyota oil filters for optimal performance and fitment.
• Verify Part Numbers: Always double-check part numbers with your VIN at a Toyota dealership or reliable parts supplier to ensure you have the correct components for your specific vehicle.

Need an oil change? Find a trusted shop on Repairius.