2020 Toyota Camry Oil Capacity, Filter & Specs
Everything you need to know about oil capacity, filter part numbers, and drain plug torque for the 2020 Toyota Camry.
AI-generated reference. Always verify torque values, fluid capacities, intervals, and procedures against the manufacturer's service manual or OEM repair information before performing work. Repairius is not liable for damage from acting on this content without verification.
Working on this 2020 Toyota Camry? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
The 2020 Toyota Camry takes 4.8 quarts (4.5 liters) of oil for the 2.5L 4-cylinder engine, 5.7 quarts (5.4 liters) for the 3.5L V6 engine, and 4.5 quarts (4.3 liters) for the 2.5L Hybrid, assuming you are changing the filter. As an ASE-certified master technician, I always emphasize that using the correct oil weight and specification is vital for modern high-efficiency engines like the ones found in the 8th generation Camry.
Below is your complete guide to changing the oil in your 2020 Toyota Camry, including capacities, filter cross-references, and torque specs.
Quick answer
- Oil Capacity: 4.8 quarts (2.5L), 5.7 quarts (3.5L V6), 4.5 quarts (Hybrid)
- Recommended Weight: 0W-16 (for 2.5L & Hybrid), 0W-20 (for 3.5L V6)
- Oil Spec: API SN PLUS, API SP, or ILSAC GF-6B (0W-16) / GF-6A (0W-20)
- OEM Oil Filter: Toyota 90915-YZZN1 (spin-on style)
- Aftermarket Filter Cross-Reference: Fram XG4967, WIX 51394, Mobil 1 M1-103A
Capacity by engine option
The 2020 Toyota Camry is available with three distinct powertrains. Be sure to check under your hood or consult your owner's manual to confirm which engine you have before purchasing oil.
| Engine | Capacity w/ Filter | Recommended Viscosity |
|---|---|---|
| 2.5L 4-Cylinder (A25A-FKS) | 4.8 Quarts (4.5 L) | 0W-16 |
| 3.5L V6 (2GR-FKS) | 5.7 Quarts (5.4 L) | 0W-20 |
| 2.5L Hybrid (A25A-FXS) | 4.5 Quarts (4.3 L) | 0W-16 |
Note: If 0W-16 is unavailable for the 2.5L engines, 0W-20 may be used for one oil change interval, but it must be replaced with 0W-16 at the next change to ensure optimal fuel economy and engine performance.
Oil change interval
Toyota recommends synthetic oil for all 2020 Camry models, which allows for longer intervals under normal conditions.
- Normal Duty: Every 10,000 miles or 12 months (whichever comes first). This applies to mostly highway driving in moderate climates without heavy loads.
- Severe Duty: Every 5,000 miles or 6 months. This is recommended if you frequently drive on dirt/dusty roads, make repeated short trips under 5 miles in freezing temperatures, idle excessively, or drive as a taxi/rideshare vehicle.
Drain plug torque
- Torque Spec: 30 ft-lbs (40 Nm)
- Crush Washer: Always replace the 12mm aluminum drain plug gasket (Toyota OEM part #90430-12031) during every oil change. Reusing the old crush washer is the number one cause of slow oil leaks.
How to change the oil
- Warm up the engine: Run the engine for a few minutes to warm the oil, which allows it to flow faster and carry away more suspended contaminants.
- Safely lift the vehicle: Secure the car on ramps or jack stands and engage the parking brake.
- Remove the splash shield: You may need to remove or fold back the access door on the lower engine cover to access the drain plug and oil filter.
- Drain the oil: Remove the 14mm drain plug and let the oil completely drain into an approved catch pan.
- Replace the drain plug: Install a new crush washer and torque the drain plug to 30 ft-lbs.
- Replace the oil filter: Remove the old spin-on filter. Lubricate the rubber gasket of the new filter with a dab of fresh oil. Spin it on until the gasket makes contact, then hand-tighten an additional 3/4 turn.
- Fill and verify: Fill the engine with the correct amount of oil. Start the engine, let it idle for 30 seconds to fill the new filter, and check for leaks. Turn off the engine, wait a few minutes, and check the dipstick to ensure the level is at the upper mark.
Common issues / tips
- Spin-on vs. Cartridge: While older generations of the Camry V6 utilized a messy cartridge-style oil filter, the 2020 models (both the A25A 4-cylinder and 2GR-FKS V6) have returned to a traditional, easy-to-replace spin-on metal filter.
- Ultra-thin 0W-16 Oil: Many DIYers are surprised by the watery consistency of 0W-16 oil. Do not be alarmed; this ultra-low viscosity is required to meet modern emissions and fuel economy standards while perfectly protecting the tight clearances in the A25A engine block.
- Oil Level Warning: If you overfill the 2.5L engine, you may trigger an engine code or experience poor running conditions due to oil frothing. Always under-fill by about half a quart initially, then top off according to the dipstick.
Need an oil change? Find a trusted shop on Repairius.
More specs for the 2020 Toyota Camry
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2020 Toyota Camry Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.