Working on this vehicle? Write estimates, send inspections & invoice customers from your phone.

    Start 14-Day Free Trial
    ← All vehicle specs
    Serpentine Belt Routing & Length

    2020 Honda Accord: Serpentine Belt Routing & Length

    Everything on this vehicle

    Your complete guide to serpentine belt length, routing, part numbers, and replacement for the 2020 Honda Accord.

    Working on this 2020 Honda Accord? Run just this one job through Repairius.

    No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.

    14-day free trial · credit card required · cancel anytime

    Quick Answer

    Here are the key specifications for the serpentine belt and related components for the 2020 Honda Accord. Note that part numbers can vary between the 1.5L and 2.0L engine options. Always verify the correct part number for your specific vehicle with your dealer or parts supplier.

    For the 1.5L Turbo Engine:

    • Belt Length & Rib Count: Approximately 49.5 inches with 6 ribs.
    • OEM Belt Part Number: 38920-6A0-A01
    • Aftermarket Belt Cross-References:
      • Gates: K060490
      • Dayco: 5060490
      • Continental: 4060490
    • Auto-Tensioner Part Number: 31170-6A0-A01
    • Idler Pulley Part Number: This engine design often integrates the idler function into other components or may not have a separate, commonly replaced idler pulley.

    For the 2.0L Turbo Engine (Non-Hybrid):

    • Belt Length & Rib Count: Approximately 51.5 inches with 6 ribs.
    • OEM Belt Part Number: 38920-6B2-A02
    • Aftermarket Belt Cross-References:
      • Gates: K060509
      • Dayco: 5060510
      • Continental: 4060509
    • Auto-Tensioner Part Number: 31170-R0A-025
    • Idler Pulley Part Number: 31190-R0A-015

    Belt Routing

    Properly routing the serpentine belt is critical for the correct operation of your engine's accessories. An incorrectly routed belt can slip off, cause damage, and leave you stranded. Before you remove the old belt, we strongly recommend taking a clear photograph of the existing belt path with your phone.

    While the exact component placement varies slightly between engines, the general path is as follows. You will be routing the belt around a series of grooved and smooth pulleys.

    1. Start by wrapping the belt around the main crankshaft pulley at the bottom of the engine.
    2. Guide the belt up to the A/C compressor, which is typically on the lower side of the engine.
    3. From the A/C compressor, route the belt to the idler pulley.
    4. Continue the path up to the alternator, usually located higher up on one side of the engine.
    5. The belt then typically goes around the power steering pump (if equipped, otherwise this pulley is absent).
    6. Next is the water pump pulley, which is crucial for engine cooling.
    7. Finally, loop the belt over the tensioner pulley. This will be the last component, as you will need to release the tension to slip the belt on.

    Double-check your routing against the photo you took or a diagram for your specific engine before applying tension.

    How to Replace the Serpentine Belt

    Replacing the serpentine belt on a 2020 Accord is a manageable task for a DIYer with the right tool. You will need a serpentine belt tool, which is a long, thin ratchet with various socket and crowfoot attachments. In many cases, a standard 3/8" drive breaker bar can also be used.

    1. Locate the Tensioner: Find the automatic belt tensioner. It's a spring-loaded pulley designed to keep the belt tight. It will have a square hole (usually 3/8") or a hex-shaped lug on it for you to attach your tool.
    2. Release Tension: Fit your serpentine belt tool or breaker bar onto the tensioner. Rotate the tensioner away from the belt to release the pressure. This will create slack in the belt.
    3. Remove Old Belt: While holding the tensioner in the released position, slip the old belt off one of the smooth pulleys (the idler or water pump is usually easiest).
    4. Install New Belt: Route the new belt around all the pulleys according to the diagram or the photo you took, leaving the tensioner pulley for last. Make sure the ribs on the belt are correctly seated in the grooves of each grooved pulley.
    5. Apply Tension: Once you are certain the belt is routed correctly, slowly release the tensioner to apply pressure to the new belt. The spring-loaded pulley will automatically set the correct tension.
    6. Final Check: Do a final visual inspection to ensure the belt is perfectly aligned in every pulley groove. Start the engine and run it for a minute to make sure the belt is tracking correctly and there are no unusual noises.

    Replacement Interval

    Modern serpentine belts are durable, but they don't last forever. Honda recommends inspecting the belt at regular service intervals. While there isn't a strict replacement schedule, most mechanics recommend proactive replacement every 60,000 to 100,000 miles. If you frequently drive in harsh conditions (extreme heat or cold), you may need to replace it sooner.

    Signs of a Failing Belt or Tensioner

    Listen and look for these warning signs that indicate your serpentine belt or tensioner may need service:

    • Squealing or Chirping: This is the most common symptom, often heard when starting the engine or running the A/C. It indicates the belt is slipping.
    • Visible Wear: Inspect the belt for cracks, fraying, glazing (shiny spots), or missing chunks of the ribs.
    • Tensioner Noise: A rumbling or grinding noise from the engine bay could be a sign of a failing bearing in the tensioner or idler pulley.
    • Pulley Wobble: Visually inspect the tensioner and idler pulleys with the engine running (use caution!). If you see any wobble, the bearing is likely worn out.
    • Accessory Issues: If your A/C isn't blowing cold, your power steering feels heavy, or your battery isn't charging (dimming lights), it could be due to a slipping or broken belt.

    Find a trusted shop on Repairius.

    Need service on your Honda Accord?

    Your vehicle and question are already filled in — just add your location.

    More specs for the 2020 Honda Accord

    Oil Capacity & Filter

    Capacity, weight, filter PN, drain plug torque, change interval.

    Fluid Type Specs

    Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.

    Coolant Capacity & Type

    Total system capacity, OEM coolant spec, flush interval, bleed tips.

    Transmission Fluid & Service

    Trans model, fluid spec, capacity, filter PN, service interval.

    Torque Specifications

    Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.

    Brake Pad & Rotor Specs

    Pad PNs, rotor size, min thickness, caliper torque.

    Tire Size & Pressure

    OEM size, cold psi, bolt pattern, wheel size, TPMS.

    Battery Size & Group

    Group size, CCA, AGM/flooded, dimensions, reset note.

    A/C Refrigerant & Oil

    R-134a or R-1234yf, charge oz, PAG oil spec.

    Bulb Sizes (Headlight, Tail, Fog)

    Headlight, fog, tail, turn, reverse, interior.

    Factory Maintenance Schedule

    Service intervals by mileage, severe-duty notes, known issues.

    Towing Capacity & Payload

    Max tow, payload, GVWR/GCWR, hitch class by trim.

    Fuse Box Diagram & Amperage

    Fuse box locations, layout, amps, and what each fuse controls.

    Wheel Alignment Specifications

    Camber, caster, toe ranges (front & rear), adjustability notes.

    Paint Color Codes

    All factory colors with paint codes, sticker location, touch-up tips.

    Wiper Blade Sizes

    Driver/passenger/rear blade size, attachment, OEM + cross-refs.

    Spark Plug Type & Gap

    Plug PN, gap, torque, interval by engine.

    Transmission & Axle Gear Ratios

    Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.

    Key Fob Programming

    DIY programming steps, FCC ID, fob PN, battery, transponder.

    Same spec — other model years

    Maintenance & repair guides

    Browse by make

    Running an auto or diesel repair shop?

    Compare Repairius to the shop software you're paying for

    $99.99/month (first location included), unlimited users, 14-day free trial.

    Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-07-25.

    Run your shop from estimate to payment

    Don't overhaul your shop. Test Repairius on your next job.

    Repairius keeps estimates, work orders, real-time job assignment, customer and vehicle history, inventory, and payments in one place — on desktop and in your pocket.

    14-day free trial · credit card required · cancel anytime

    Not a mechanic? Send Repairius to your shop — they can run estimates, jobs, and invoices in one place.

    Know someone who needs this?

    Share this page with a mechanic, a shop owner, or a friend working on the same problem.

    Know a mechanic or shop owner Repairius could help?

    Send them Repairius in one tap. Free listing, online booking, reminders and the full shop workflow.

    Text them Email