Working on this vehicle? Write estimates, send inspections & invoice customers from your phone.

    Start 14-Day Free Trial
    ← All vehicle specs
    Coolant Capacity & Type

    2024 Kenworth W900 Coolant Capacity & Type Guide

    An ASE-certified master technician's guide to the 2024 Kenworth W900 cooling system, capacities, and maintenance.

    Working on this 2024 Kenworth W900? Run just this one job through Repairius.

    No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.

    14-day free trial · credit card required · cancel anytime

    Quick answer — 2024 Kenworth W900

    Cummins X15
    50 - 80 quarts (47.3 - 75.7 liters)
    PACCAR MX-13
    48 - 75 quarts (45.4 - 70.9 liters)

    From the table below. Confirm with your owner's manual for your exact engine.

    The 2024 Kenworth W900 cooling system holds approximately 48 to 80 quarts (12 to 20 gallons, or 45.4 to 75.7 liters) of coolant, depending on the specific engine equipped, radiator size, and the presence of auxiliary equipment like sleeper cabin heaters or Auxiliary Power Units (APUs). As an ASE-certified master technician, I can tell you that managing the cooling system on a heavy-duty Class 8 truck like the W900 is vastly different from a passenger vehicle, requiring specific heavy-duty coolants and meticulous maintenance to keep that big bore diesel running at optimal temperatures.

    Quick answer

    • Total cooling system capacity: 48 – 80 quarts (45.4 – 75.7 liters / 12 – 20 gallons) depending on chassis, engine, and sleeper configuration.
    • OEM coolant spec: Heavy-Duty Extended Life Coolant (ELC). This is a Nitrite-Free OAT (Organic Acid Technology) coolant, typically Red in color. It must meet Cummins CES 14603 (for Cummins engines) or the equivalent PACCAR specification.
    • Mix ratio: 50/50 pre-mix of coolant and deionized/distilled water. Never use straight concentrate without mixing, and avoid tap water to prevent scale buildup.

    Capacity by engine option

    Because the Kenworth W900 is a highly customizable truck built for various vocational and long-haul applications, the exact capacity varies based on frame length, radiator package, and sleeper size. Always check the capacity decal under the hood or your specific build sheet.

    Engine OptionEstimated Total System Capacity (Qts / L)
    Cummins X1550 - 80 quarts (47.3 - 75.7 liters)
    PACCAR MX-1348 - 75 quarts (45.4 - 70.9 liters)

    Note: Trucks equipped with massive 86-inch Studio Sleepers or tied into aftermarket APUs will fall on the highest end of this capacity spectrum due to the long coolant lines running to the rear heater cores.

    Flush interval

    Modern Heavy-Duty Extended Life Coolants (ELC) are incredibly robust, but they still have a finite lifespan, especially under the grueling conditions of commercial trucking.

    • Normal Duty / Highway: Typically, OAT ELC can last up to 600,000 miles, 12,000 engine hours, or 6 years (whichever comes first) before requiring a complete flush and fill. Some formulations offer a "life of the engine" guarantee if an extender/booster is added at 300,000 miles, but always verify with your specific coolant brand.
    • Severe Duty / Vocational / High Idle: If your W900 is used for heavy hauling, logging, or experiences high idle times, it is highly recommended to flush the system every 300,000 miles, 6,000 hours, or 3-4 years to prevent acidic buildup and protect wet sleeve cylinder liners from cavitation.

    How to refill & bleed

    Bleeding a Class 8 truck with a sleeper cab can be notoriously difficult due to the sheer volume of fluid and the length of the heater hoses.

    1. Prepare the truck: Ensure the engine is completely cold. Turn the key to the ON position (engine off) and turn the cabin and sleeper climate controls to maximum heat to open all heater control valves.
    2. Vacuum fill (Recommended): Because of the long lines to the sleeper heater core, using a heavy-duty pneumatic vacuum coolant filler is strongly recommended. This tool pulls the entire system into a deep vacuum and draws the pre-mixed coolant in, eliminating massive air pockets instantly.
    3. Manual fill (If vacuum tool is unavailable): Pour the 50/50 ELC mix slowly into the surge tank to minimize aeration. Fill to the "MAX" line.
    4. Bleed the air: Locate the air bleed petcock on the thermostat housing (standard on Cummins X15) and open it slightly to let trapped air escape while filling. Close it once a steady stream of coolant appears.
    5. Warm up: Start the engine and let it run at a high idle. Keep the surge tank cap off initially. Monitor the coolant level as the thermostat opens and the fluid cycles through the sleeper lines. Add coolant as the level drops. Once the level stabilizes and hot air blows from both the dash and sleeper vents, install the pressure cap.

    Common cooling system issues

    For the current generation of Kenworth W900s running modern big-bore diesels, a few specific issues are worth monitoring:

    • EGR Cooler Leaks: Modern emissions systems route extremely hot exhaust gases through the EGR cooler. Over time, thermal cycling can cause internal fatigue, leading to coolant weeping into the exhaust or intake. If you are losing coolant but see no external leaks, suspect the EGR cooler.
    • Hose Clamp Degradation: With heavy vibrations, standard worm-gear clamps can loosen or cut into silicone coolant hoses. Upgrading to or inspecting the heavy-duty constant-tension spring clamps is vital to prevent cold-water leaks.
    • Water Pump Weepage: Both the MX-13 and X15 engines can occasionally experience premature water pump seal weeping. A slight crust around the weep hole is normal, but active dripping requires immediate replacement.

    Find a trusted shop on Repairius.

    Need service on your Kenworth W900?

    Your vehicle and question are already filled in — just add your location.

    More specs for the 2024 Kenworth W900

    Oil Capacity & Filter

    Capacity, weight, filter PN, drain plug torque, change interval.

    Fluid Type Specs

    Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.

    Transmission Fluid & Service

    Trans model, fluid spec, capacity, filter PN, service interval.

    Torque Specifications

    Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.

    Brake Pad & Rotor Specs

    Pad PNs, rotor size, min thickness, caliper torque.

    Tire Size & Pressure

    OEM size, cold psi, bolt pattern, wheel size, TPMS.

    Battery Size & Group

    Group size, CCA, AGM/flooded, dimensions, reset note.

    A/C Refrigerant & Oil

    R-134a or R-1234yf, charge oz, PAG oil spec.

    Bulb Sizes (Headlight, Tail, Fog)

    Headlight, fog, tail, turn, reverse, interior.

    Factory Maintenance Schedule

    Service intervals by mileage, severe-duty notes, known issues.

    Towing Capacity & Payload

    Max tow, payload, GVWR/GCWR, hitch class by trim.

    Fuse Box Diagram & Amperage

    Fuse box locations, layout, amps, and what each fuse controls.

    Serpentine Belt Routing & Length

    Belt routing, length, rib count, OEM + aftermarket PNs.

    Wheel Alignment Specifications

    Camber, caster, toe ranges (front & rear), adjustability notes.

    Paint Color Codes

    All factory colors with paint codes, sticker location, touch-up tips.

    Wiper Blade Sizes

    Driver/passenger/rear blade size, attachment, OEM + cross-refs.

    Spark Plug Type & Gap

    Plug PN, gap, torque, interval by engine.

    Transmission & Axle Gear Ratios

    Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.

    Key Fob Programming

    DIY programming steps, FCC ID, fob PN, battery, transponder.

    Same spec — other model years

    Maintenance & repair guides

    Browse by make

    Running an auto or diesel repair shop?

    Compare Repairius to the shop software you're paying for

    $99.99/month (first location included), unlimited users, 14-day free trial.

    Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-09-18.

    Driving or Managing a Fleet?

    Use Dispatchtool for truck navigation, driver communication, dispatching, and fleet management.

    Visit Dispatchtool
    Run your shop from estimate to payment

    Don't overhaul your shop. Test Repairius on your next job.

    Repairius keeps estimates, work orders, real-time job assignment, customer and vehicle history, inventory, and payments in one place — on desktop and in your pocket.

    14-day free trial · credit card required · cancel anytime

    Not a mechanic? Send Repairius to your shop — they can run estimates, jobs, and invoices in one place.

    Know someone who needs this?

    Share this page with a mechanic, a shop owner, or a friend working on the same problem.

    Know a mechanic or shop owner Repairius could help?

    Send them Repairius in one tap. Free listing, online booking, reminders and the full shop workflow.

    Text them Email