2024 Kenworth W900 Fuse Box Diagram
A complete guide to the fuse and relay locations, amperages, and circuits for the 2024 Kenworth W900.
Working on this 2024 Kenworth W900? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Navigating the complex electrical system of a 2024 Kenworth W900 is critical for any owner or technician. Understanding the location and function of your fuses and relays can save you significant time and money when troubleshooting issues. This guide provides a comprehensive overview of the fuse box locations, diagrams, and common issues related to the W900's electrical system.
Quick Answer
Your 2024 Kenworth W900 has two primary fuse and relay centers:
- In-Cab Fuse Panel: The main fuse panel is located inside the cab, on the passenger side. It's typically behind a kick panel or a designated access door near the floor, against the firewall.
- Under-Hood Power Distribution Center: A secondary box containing high-amperage fuses and critical system relays is located in the engine compartment, usually on the driver's side near the firewall or air cleaner housing.
Disclaimer: Fuse assignments and locations can vary significantly based on your truck's specific configuration (sleeper cab vs. day cab, engine model, and other optional equipment). Always consult the printed diagram on the inside of your fuse box cover for the most accurate information for your specific vehicle.
In-Cab Fuse Panel
The main fuse panel inside the cab houses the majority of fuses for chassis and cab functions. You'll need to remove a panel on the passenger side to access it. Below are common circuits you will find here.
| Fuse # | Amp | Color | Circuit / Component Protected |
|---|---|---|---|
| F1 | 15A | DK Blue | Horn |
| F2 | 10A | Red | Airbag / SRS Control Module |
| F3 | 20A | Yellow | Cigar Lighter / 12V Power Port 1 |
| F4 | 20A | Yellow | 12V Power Port 2 |
| F5 | 15A | DK Blue | Trailer Brake Controller |
| F6 | 30A | Green | Blower Motor (HVAC Fan) |
| F7 | 10A | Red | Ignition Switch |
| F8 | 15A | DK Blue | Turn Signals |
| F9 | 10A | Red | ABS Control Unit (Key Power) |
| F10 | 20A | Yellow | Fuel Heater |
| F11 | 15A | DK Blue | Low Beam Headlight (Left) |
| F12 | 15A | DK Blue | Low Beam Headlight (Right) |
| F13 | 10A | Red | High Beam Headlight (Left) |
| F14 | 10A | Red | High Beam Headlight (Right) |
| F15 | 10A | Red | Park / Tail Lights (Left) |
| F16 | 10A | Red | Park / Tail Lights (Right) |
| F17 | 20A | Yellow | Stop / Brake Lights |
| F18 | 20A | Yellow | Main Radio / Infotainment Power |
| F19 | 10A | Red | Instrument Cluster |
| F20 | 5A | Tan | Engine Control Module (ECM) - Wakeup |
| F21 | 15A | DK Blue | Windshield Wipers |
| F22 | 10A | Red | A/C Clutch |
| F23 | 25A | Natural | Sleeper Power |
| Relay # | Type | Circuit / Component Controlled | |
| R1 | ISO | Starter Relay | |
| R2 | ISO | Blower Motor Relay | |
| R3 | ISO | A/C Clutch Relay | |
| R4 | ISO | Park Lamp Relay |
Under-Hood Power Distribution Center
This secondary box contains larger fuses and main relays that distribute power to high-draw systems and the main fuse panel itself. It protects the core functions of the powertrain and chassis.
| Fuse # | Amp | Color | Circuit / Component Protected |
|---|---|---|---|
| F101 | 30A | Green | Engine Control Module (ECM) - Main Power |
| F102 | 30A | Green | Transmission Control Module (TCM) |
| F103 | 25A | Natural | ABS Pump Motor |
| F104 | 40A | Orange | Main Ignition Feed |
| F105 | 20A | Yellow | Fuel Pump |
| F106 | 30A | Green | Aftertreatment System |
| F107 | 60A | Blue | Main Cabin Fuse Panel Feed |
| F108 | 15A | DK Blue | Engine Sensor Power |
| Relay # | Type | Circuit / Component Controlled | |
| R101 | HD ISO | Main Power Relay | |
| R102 | HD ISO | ECM Power Relay | |
| R103 | HD ISO | Fuel Pump Relay |
How to Test a Fuse
If a component stops working, a blown fuse is a likely culprit. You can test a fuse in two simple ways:
-
Visual Inspection: Pull the suspect fuse from its slot. Hold it up to a light source. Inside the plastic body of the fuse is a small metal strip. If this strip is broken or looks burnt, the fuse is blown and needs to be replaced. If it's intact, the fuse is likely good.
-
Multimeter Test: For a more definitive test, you can use a digital multimeter set to the continuity setting (often indicated by a sound icon). Touch one probe to each metal blade on the top of the fuse. If the multimeter beeps or reads close to zero ohms, the fuse is good. If it remains silent and shows "OL" or no change, the fuse is blown.
Always replace a blown fuse with one of the exact same amperage rating. Using a higher-rated fuse can cause severe damage to the electrical system and create a fire hazard.
Common Blown Fuses on the 2024 Kenworth W900
While any fuse can blow, some are more common than others due to the circuits they protect.
-
Cigar Lighter / 12V Power Port: This is arguably the most common blown fuse on any commercial truck. It's usually caused by a faulty phone charger, a loose plug, or a foreign object (like a coin) falling into the socket and causing a short circuit. Before replacing the fuse, unplug all devices and inspect the socket for debris.
-
Trailer Lights/Brake Controller: Trailer wiring is a frequent source of electrical problems. A short circuit in the trailer's wiring, a corroded 7-pin connector, or a fault in the trailer brake system can cause these fuses to blow repeatedly. If you replace the fuse and it blows as soon as you connect a trailer, the fault is almost certainly with the trailer, not the truck.
-
Radio / Infotainment: If your radio or main screen goes dead, the fuse is the first place to look. This can sometimes be caused by an internal fault in the unit, but it's also worth checking if any aftermarket devices (like a satellite radio or GPS) have been wired into the radio's power source improperly.
Troubleshooting electrical issues can be a daunting task. If you've checked the fuses and are still experiencing problems, it may be time to consult a professional. For complex diagnostics and repairs, it's always best to rely on a certified technician.
Find a trusted shop on Repairius.
Before you pull a fuse on the 2024 Kenworth W900
- Use the label printed on the panel cover or the owner's manual for your exact build. Layouts change with options, model year and build date, so a chart for another truck can be wrong.
- Replace a blown fuse only with the same amp rating. A larger fuse can let wiring overheat.
- A fuse that blows again right away means a short or failing component downstream. Find the cause before replacing it again.
- A good fuse doesn't prove the circuit works — relays, grounds and connectors fail too.
- Many heavy trucks have more than one power distribution point (cab, under-hood or near the batteries), and some circuits use circuit breakers instead of fuses. Some systems have 24-volt starting circuits; confirm the voltage before testing.
- Disconnect the battery before working near high-current fuses or cables.
Learn more: How fuses, relays and truck electrical systems work · Find mobile truck repair
Need service on your Kenworth W900?
Your vehicle and question are already filled in — just add your location.
More specs for the 2024 Kenworth W900
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Spark Plug Type & Gap
Plug PN, gap, torque, interval by engine.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2024 Kenworth W900 Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.
Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-07-12.